Recent Posts

Pages: 1 [2] 3 4 5 6 7 ... 10
11
Spencer Shooting Society / Re: Photos Posted of my Cimarron carbine
« Last post by Macon Due on Today at 04:16:15 PM »
Abilene
Yes, it is beautiful for sure. I had reservations about sending it back for repairs as to not getting the same carbine or wood back.
Thank you........Macon
12
The Leather Shop / Re: New project holster/belt
« Last post by Crossdrawnj on Today at 04:05:42 PM »
Thanks to you both for your advise.  Would you use slightly heavier leather for the belt?
13
BROW / Revolvers with Buffalo rifles
« Last post by U.S.M.R. on Today at 02:47:18 PM »
What revolver do you like with your rifles? I know that times were hard. Cap and ball revolvers were plentiful and cheap. I like my Cimarron .44 American with my Sharps, Remingtons, and Trap Doors. Conversions were available. You couldn’t get a SAA until 74. Your thoughts.
14
Spencer Shooting Society / Re: Photos Posted of my Cimarron carbine
« Last post by Abilene on Today at 11:46:44 AM »
Wow, that's the nicest wood I've seen on a Spencer!
15
Spencer Shooting Society / Re: Photos Posted of my Cimarron carbine
« Last post by El Supremo on Today at 10:12:24 AM »
Great news:
Please share which Accurate mould and the requested diameter to which you asked it cast.  Thanks.
El Supremo/Kevin Tinny
16
Tall Tales / Re: May we move on, for coffee and chat ?
« Last post by Silver Creek Slim on Today at 07:21:26 AM »
Morning y'all.
Coffee and tea are ready.

Some videos are uploaded. More are currently uploading. Slow Internet connection.  ::)

'Tis 45 and overcast. "Showers likely and a chance of thunderstorms. Highs in the upper 60s. South wind 5 to 10 mph. Chance of rain 70 percent."

Slim
17
CAS City Classifieds / Re: Shortened krag replacement stock and forend for sale.
« Last post by Ironbadger on Today at 06:58:59 AM »
Why I wound up not needing it?

Because I got an excellent deal on a full length unfinished 1898 stock and handguard later on, and I am not building two rifles.

Badger
18
CAS City Classifieds / Shortened krag replacement stock and forend for sale.
« Last post by Ironbadger on Today at 06:56:10 AM »
Need to find my camera and take pics..
But this is a finished replacement stock and unfinished forend wood I picked up for a Krag rifle and wound up not using.

Its cut off at the lower band, so should be easy enough to glue and pin the forend onto it for a full length stock.

I have an unfinished handguard cut for a 1905 model to go in the deal as well. (pretty sure its a 1905? its for the rear sight that has the windage swivel base, I believe.)

$200 and whatever the shipping turns out to be.

If theres interest, I'll get some pics up when I figure out where the camera wound up.






-Badger
19
Gunsmithing / Re: Rossi 92 parts- will older interarms era parts fit newer guns?
« Last post by Froogal on Today at 06:19:26 AM »
Quote from: DeaconKC on Yesterday at 08:14:05 PM
Okay, here's the easy way to eliminate the safety. Drive the pin out that holds the safety in, remove the three parts. Take a .25 ACP case and cut it down to about an 1/8"-3/16" and Blue Lock-tite it in place. If you can find a W-W stamped case it looks even better.

And be aware there is a detent ball and spring in there. I saved the spring but the ball went to parts unknown.
20
Tall Tales / Re: May we move on, for coffee and chat ?
« Last post by Coffinmaker on Today at 06:11:56 AM »

 :)  Hey Deacon  ;)

Now all ya need a couple Large magnetic signs for Howard - Fine & Howard for the sides of the Van you betcha!!!  Yer a DAISY iffin ya don't!! (Snicker Snicker)  ::)
Pages: 1 [2] 3 4 5 6 7 ... 10
SMF spam blocked by CleanTalk
© 1995 - 2023 CAScity.com