Author Topic: Percussion caps for Uberti revolvers  (Read 800 times)

Offline Sandlapper

  • Citizen
  • *
  • Posts: 24
  • Liked:
  • Likes Given: 2
Percussion caps for Uberti revolvers
« on: November 19, 2023, 06:44:02 PM »
Can anyone advise as to the best percussion caps currently available for use with the stainless aftermarket nipples and Uberti revolvers and the best place to buy them? Everyone seems to be on backorder, or if they do have any, the price is outrageous. Thanks, Sandlapper

Offline Coffinmaker

  • Top Active Citizen
  • *
  • Posts: 7585
  • Liked:
  • Likes Given: 124
Re: Percussion caps for Uberti revolvers
« Reply #1 on: November 20, 2023, 08:31:26 AM »

 :) Sandlapper  ;)

Your question is unfortunately mostly a dead end currently.  As you have discovered, Percussion Caps are currently The Holy Grail.  Your only recourse is to constantly shop the obvious suppliers and "JUMP" Immediately.  Regardless, prices will probably continue to be "outrageous" for the foreseeable future.  Supply is short.  Addendum:

Remington 10 or 11
RWS 1075
CCI # 11 (may work)

SlixShot nipples are optimized for Remington #10

GOOD LUCK  8)

Offline Sandlapper

  • Citizen
  • *
  • Posts: 24
  • Liked:
  • Likes Given: 2
Re: Percussion caps for Uberti revolvers
« Reply #2 on: November 20, 2023, 02:22:44 PM »
Thanks for your advice. Will do.  Regards, Sandlapper

Advertising

  • Guest
Re: Percussion caps for Uberti revolvers
« Reply #3 on: Today at 09:32:50 PM »

Offline Professor Marvel

  • purveyor of useless items to the gentry
  • Deputy Marshal
  • Top Active Citizen
  • *
  • Posts: 3059
  • learn from the past, or be doomed to repeat it
  • Liked:
  • Likes Given: 1078
Re: Percussion caps for Uberti revolvers
« Reply #3 on: November 20, 2023, 04:16:21 PM »
As our good Coffin has remarked, if you find ANY percussion caps, 10, 11, ANY brand,
GRAB them!

One can always “resize” them gently or trade them off for what fits your tubes,
Or even get several different sets of tubes (nipples) and chuck them in a drill and file them down to
Fit what you can get ( ie fit the tubes to the available caps, instead of fitting caps to tubes).

Just be certain to mark each set of six tubes so you know what you have….

Even BP is hard to find, now only available via orders…



Yhs
Prof mumbles
Your Humble Servant
~~~~~Professor Algernon Horatio Ubiquitous Marvel The First~~~~~~
President, CEO, Chairman,  and Chief Bottle Washer of


Professor Marvel's
Traveling Apothecary
and
Fortune Telling Emporium


Acclaimed By The Crowned Heads of Europe
Purveyor of Patent Remedies, Snake Oil, Powder, Percussion Caps, Cleaning Supplies, Dry Goods,
and
Picture Postcards

Offering Unwanted Advice for All Occasions
and
Providing Useless Items to the Gentry
Since 1822
[
Available by Appointment for Lectures on Any Topic


Offline Crow Choker

  • Top Active Citizen
  • *
  • Posts: 1103
  • River Banker Extraordinaire
  • Liked:
  • Likes Given: 36
Re: Percussion caps for Uberti revolvers
« Reply #4 on: November 20, 2023, 04:59:53 PM »
High Fives to Coffinmaker on his post with a few added comments. Most if not all of the aftermarket nipples do well with Rem 10's. They have the proper dimensions to fit over caps, fit snuggly, and have the longest outside petals to fit over the nipples. CCI 11's are next, followed by RWS 1045's. Rem 11's have shorter petals, shorter than Rem 10's, CCI 11's, and the RWS 1045's in that order.

 What Rem 11's I have used, and they were holdovers from my percussion TC caplock rifle, the Rem 11's didn't fit as tight and fell off of the nipples more than the others after firing due to having shorter petals not adhering to the nipple. This can be bad if the cap fragments fall into your revolver action. Using the three others I mentioned, they still fit tight enough to stay on the nipples after firing for the most part, just needing a flick with a fingernail to dislodge.

 CCI 10's are a tight fitting cap, on most nipples with a few exceptions require hard seating and, in my experience, fail to even seat firmly some on caps, either original or aftermarket. Avoid them if possible. Many have written of this. Too tight of an inside dimension and shorter outside length petals. I have probably 475 of the 500 I bought some years ago before knowing of the dimension of them that I have no use for. I had to use a wooden dowel to seat and gritted my teeth hoping I wouldn't cause them to fire. Wouldn't be a harmonious outcome.

 As Coffin suggested, buy when you find, but watch any seller that is really trying to scalp ya. A good posting on this forum can be found on the Darkside section. At the top you'll find the Dark Arts. Click on that, go around 2/3's of the way down and you'll find a thread posted by Mako titled 'Cap Gun Primer: Correct Cone Length' (cone--another word used by some for nipples). Around 4 pages long, Mako gives very good CAD pictures, explanations, and charts of the use of various nipples and percussion cap relationships. There is a very informative chart showing the dimensions of available percussion caps available. This was posted before SlixShots, but Slix's, Treso's, and Track of the Wolf nipples are all pretty much the same in size but differ in material and a few other construction this and that. FWIW, nipples and caps pretty much follow the same sizing requirements and need be the revolver be a Uberti or Pietta. A Ruger Old Army pretty much has its own sizing, but the Rem 10's in my shooting are the best also.

 Factory nipples pretty much IMO and experience follow the same cap/nipple relationship as the aftermarkets with a few exceptions. I've found when comparing all of the nipples I've mentioned and brands/sizes of percussion caps Rem #10's are the best followed by CCI 11's, then RWS 1045's. IMO due to the shortage of caps being offered by retail outlets, if ya find some of the three I mentioned as being the best,  invest in more than ya think you'll need, if not you'll be on the search for more after the one or two tins ya buy at the time are shot up. See the Professor chimed in, don't agree with that approach and method, but he is a good guy.
Darksider-1911 Shooter-BOLD Chambers-RATS-SCORRS-STORM-1860 Henry(1866)-Colt Handgun Lover an' Fan-NRA-"RiverRat"-Conservative American Patriot and Former Keeper & Enforcer of the Law an' Proud of Being Both! >oo

Offline treebeard

  • Top Active Citizen
  • *
  • Posts: 484
  • Liked:
  • Likes Given: 16
Re: Percussion caps for Uberti revolvers
« Reply #5 on: December 05, 2023, 06:27:46 PM »
So what has caused the percussion cap shortage?

Offline Professor Marvel

  • purveyor of useless items to the gentry
  • Deputy Marshal
  • Top Active Citizen
  • *
  • Posts: 3059
  • learn from the past, or be doomed to repeat it
  • Liked:
  • Likes Given: 1078
Re: Percussion caps for Uberti revolvers
« Reply #6 on: December 05, 2023, 10:46:53 PM »
So what has caused the percussion cap shortage?

Oh My that is a topic all by itself.

We can start with the first covid global supply bottleneck of , well, everything!
Any ammunition stuff immediately became unobtainium and materials & labor went to govt contracts first.

Add to that,  the supergiant container ship “Evergreen” blocking the Suez Canal for many weeks. That event alone
Caused a blockeage and delay of almost 400 other ships, which dominoed down the supply chain.

Penultimately, percussion caps are not exactly on the priority list for manufacturors, so …..

During primer shortages, I experimented with modifying percussion caps into low pressure small pistol primers.
Now I have to go the other direction LOL. Or get a Tap-o-Cap ….

One only has to look back at the “Rifleman” articles from 1940-1946 to see that such shortages are not that
Uncommon and we just have to adjust accordingly….
Your Humble Servant
~~~~~Professor Algernon Horatio Ubiquitous Marvel The First~~~~~~
President, CEO, Chairman,  and Chief Bottle Washer of


Professor Marvel's
Traveling Apothecary
and
Fortune Telling Emporium


Acclaimed By The Crowned Heads of Europe
Purveyor of Patent Remedies, Snake Oil, Powder, Percussion Caps, Cleaning Supplies, Dry Goods,
and
Picture Postcards

Offering Unwanted Advice for All Occasions
and
Providing Useless Items to the Gentry
Since 1822
[
Available by Appointment for Lectures on Any Topic


Offline Coffinmaker

  • Top Active Citizen
  • *
  • Posts: 7585
  • Liked:
  • Likes Given: 124
Re: Percussion caps for Uberti revolvers
« Reply #7 on: December 06, 2023, 09:24:24 AM »
 :) Treebeard  ;) [formerly freeboard - thanks OTTO]  >:(

Even though it hasn't garnered much national attention, the CDC is currently investigating a strange new Virus, named "Lak-A-Capa" that has emerged and is currently strangling the supply chain.  Most manufactures have admitted this virus has virtually shut down their Percussion Cap Manufacturing.  Currently, there is no known Vaccine  ::)

Stay Tuna

(I absolutely HATE OTTO)

Offline DrLogik

  • Citizen
  • *
  • Posts: 5
  • Liked:
  • Likes Given: 0
Re: Percussion caps for Uberti revolvers
« Reply #8 on: December 13, 2023, 08:38:36 PM »
My local gun shop has percussion caps but you're right, the last time I bought them online was mid-November and all the retailers appear to be out of stock now.

Offline hammerdown

  • Citizen
  • *
  • Posts: 2
  • Liked:
  • Likes Given: 0
Re: Percussion caps for Uberti revolvers
« Reply #9 on: February 12, 2024, 05:27:16 PM »
I am trying to convert to 209 for my pistols have done all my rifles to 209 now working on the pistols more than one way to skin a cat

 

SMF spam blocked by CleanTalk

© 1995 - 2023 CAScity.com