« previous next »
Pages: 1 [2]   Go Down

Author Topic: Remington Elliot Ring Trigger 4 Barrel Pistol  (Read 1062 times)

Offline Marshall Matt Dillon

  • Citizen
  • *
  • Posts: 9
  • Liked:
  • Likes Given: 1
Re: Remington Elliot Ring Trigger 4 Barrel Pistol
« Reply #20 on: December 29, 2020, 09:03:19 PM »
Got my cases and bullets today in mail. Now to trim cases and figure out how to reload them.
Logged

Offline ndnchf

  • Top Active Citizen
  • *
  • Posts: 1153
  • Liked:
  • Likes Given: 0
Re: Remington Elliot Ring Trigger 4 Barrel Pistol
« Reply #21 on: December 30, 2020, 04:22:45 AM »
Lucky you. Mine are still in USPS limbo somewhere in Maryland!
Logged
"We're all travelers in this world.  From the sweet grass to the packing house, birth till death, we travel between the eternities"  Prentiss Ritter, Broken Trail

Offline Marshall Matt Dillon

  • Citizen
  • *
  • Posts: 9
  • Liked:
  • Likes Given: 1
Re: Remington Elliot Ring Trigger 4 Barrel Pistol
« Reply #22 on: December 30, 2020, 09:19:47 AM »
can i smear lube on bullet with my fingers? Never lubed bullets before.
Logged

Offline ndnchf

  • Top Active Citizen
  • *
  • Posts: 1153
  • Liked:
  • Likes Given: 0
Re: Remington Elliot Ring Trigger 4 Barrel Pistol
« Reply #23 on: December 30, 2020, 10:30:21 AM »
Sure. That will work. Use appropriate lube for the powder you use.
Logged
"We're all travelers in this world.  From the sweet grass to the packing house, birth till death, we travel between the eternities"  Prentiss Ritter, Broken Trail

Offline ndnchf

  • Top Active Citizen
  • *
  • Posts: 1153
  • Liked:
  • Likes Given: 0
Re: Remington Elliot Ring Trigger 4 Barrel Pistol
« Reply #24 on: January 10, 2021, 09:50:31 AM »
My reloadable cases from Jack Harrison finally arrived after more than 3 weeks in USPS limbo. Here is what I did to prepare them.

First I cut them to about .600" length with the chop saw. Then trimmed to final length of .575". Lastly the mouths were neck reamed to. 299" to fit the .299" diameter heel of the bullets. This last step may not be necessary unless you have a tight chamber. But I had the neck reamer, so I reamed them to make seating the bullets easier. After chamfering the case mouths, they were ready to load  ;D
Logged
"We're all travelers in this world.  From the sweet grass to the packing house, birth till death, we travel between the eternities"  Prentiss Ritter, Broken Trail

Advertisers

  • Guest
Re: Remington Elliot Ring Trigger 4 Barrel Pistol
« Reply #25 on: Today at 09:46:43 AM »
Logged

Offline ndnchf

  • Top Active Citizen
  • *
  • Posts: 1153
  • Liked:
  • Likes Given: 0
Re: Remington Elliot Ring Trigger 4 Barrel Pistol
« Reply #25 on: January 10, 2021, 10:00:28 AM »
I loaded one starter pistol blank with no powder or bullet to test functionality. I stepped out the back door and it went bang  :D

So I loaded up 8 cartridges using the starter blank, 4.0gr of Old E  3F and my slightly shortened Ideal 299153 bullets. Since I don't have a crimp die, I used 2 drops of loctite, kind of a chemical crimp  ;D.  Finally, the bullets were lubed with an old time factory heel bullet lube.

I now have 8 rounds ready to test fire  :D  :D
Logged
"We're all travelers in this world.  From the sweet grass to the packing house, birth till death, we travel between the eternities"  Prentiss Ritter, Broken Trail

Offline dusty texian

  • Chief Scout Wehmeyer Ranch's.
  • Top Active Citizen
  • *
  • Posts: 1998
  • Dusty Texian
  • Liked:
  • Likes Given: 57
Re: Remington Elliot Ring Trigger 4 Barrel Pistol
« Reply #26 on: January 11, 2021, 11:06:03 AM »
Very cool little cartridges . You did good Amigo . ,,,,,,DT
Logged
Pages: 1 [2]   Go Up
« previous next »
 

SMF spam blocked by CleanTalk

© 1995 - 2020 CAScity.com