Author Topic: Winchester 1897 short chamber?  (Read 443 times)

Offline Dirty Dick

  • Top Active Citizen
  • *
  • Posts: 136
  • Liked:
  • Likes Given: 15
Winchester 1897 short chamber?
« on: November 15, 2020, 06:21:38 PM »
I bought a nice old 1897 Winchester 1922 takedown model with 30" full choke for cowboy matches, is it possible the chamber might be a bit short for 2 3/4" pie crimp (modern) shells, as all shotshells of the era were roll crimp? It seems to have more recoil using the same ammo as my M12 Winchester.  ???
NRA Life, CSSA, RCA,

Offline Professor Marvel

  • purveyor of useless items to the gentry
  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 2705
  • learn from the past, or be doomed to repeat it
  • Liked:
  • Likes Given: 329
Re: Winchester 1897 short chamber?
« Reply #1 on: November 15, 2020, 10:03:26 PM »
My Good D-D

Since your '97 is an old original dating to 1922 you ALMOST CERTAINLY have the shorter chamber or at the very least a shorter forcing cone unless someone else had it reemed.

snips from "from The High Road":
"The '97 chamber is 2 5/8". In order to shoot 2 3/4" shells with star crimps, you're going to have to have it rechambered. Even the guns marked 2 3/4" on the barrels were made for the old roll crimped shells, and are about 1/8" too short. The shells will fit and fire, but when the star crimp opens up, the plastic is protuding into the forcing cone, restricting it. This increases pressure dramatically and will crack the frame."

"When your shotgun was new, the only shotgun shells available were roll crimped. Now all that's available are star crimped. When the two crimps open upon firing, the mouth of the star crimp extends about 1/8" to 3/16" into the forcing cone farther than a roll crimp does."

hope this helps
prf marvel
Your Humble Servant
~~~~~Professor Algernon Horatio Ubiquitous Marvel The First~~~~~~
President, CEO, Chairman,  and Chief Bottle Washer of
Professor Marvel's
Traveling Apothecary
and
Fortune Telling Emporium


Acclaimed By The Crowned Heads of Europe
Purveyor of Patent Remedies, Snake Oil, Powder, Percussion Caps, Cleaning Supplies, Dry Goods,
and
Picture Postcards

Offering Unwanted Advice for All Occasions
and
Providing Useless Items to the Gentry
Since 1822
[
Available by Appointment for Lectures on Any Topic

Offline Professor Marvel

  • purveyor of useless items to the gentry
  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 2705
  • learn from the past, or be doomed to repeat it
  • Liked:
  • Likes Given: 329
Re: Winchester 1897 short chamber?
« Reply #2 on: November 15, 2020, 10:18:34 PM »
Here is more from The High Road

https://www.thehighroad.org/index.php?threads/winchester-97-chamber-size.390434/
snip-------------------------------------------
    Some clarification is in order.
    The barrels from Winchester of classic era had plenty of barrels on 97's that had no chamber length markings, but measure the same as those barrels WITH 2-3/4" markings.
    For instance: every Model 37 12 ga. is a 2-3/4" marked barrel, but measures as a nominal 2-5/8" or 2.6"
    A pair of Model 12 16 ga. barrels marked 2-3/4" that measure at about 2.6"
    A pair of '97 barrels with patent marks of 1900 and 1901 measure the same as an "E" model, about 2.6"

    The only typical problem vs. paper/ plastic hulls is in the port configuration on M-12's, for instance, not wanting to clear a more stubborn star crimp end of a plastic hull.

    Was there going to be necessity to mark a barrel already proofed for the most modern length shell available at the time (2-3/4")? The 3" magnums didn't come out till much later, and that is when all new barrels would have been prudent to mark.

    Realize that every one of those barrels would have been proofed by Winchester and claimed by them to be safe at the time of manufacture. If they are marked 2-3/4, they should be considered safe. If they measure the same as one marked 2-3/4, they should be considered safe, regardless of lack of marking.
    See that proof mark on the barrel? Every factory marked Winchester barrel will have one. That barrel and the gun are safe. A mechanical check of the safety and locking parts of the mechanism are more important than chamber length precision.

    Those chamber lengths, regardless of whether marked or unmarked, being within 1/8" of a full 2-3/4", have no significant pressure change compared to any other chamber that is at 2-3/4", and are not in any way a danger to the frame or shooter. Period.

    I don't discourage lengthening forcing cones for better patterns, if done the way that I do them, but chamber lengthening is not something I would push by fear-mongering.

    Any tale of a short chamber causing extreme pressure is something I had once believed myself, but no longer.
    Any '97 frame cracking is NOT caused by a measly 1/8" of chamber. NO way, no how.

    I don't see how anybody could make that claim (honestly) if they had no idea of the history of the gun- once owned by an amateur reloader, for instance.

    Reloading with wrong powder/charge MAY do something to the safety factor, but even the more fear-mongered example of shooting 3" shells in a 2-3/4" chambered barrel does not make the 3" shell have any significant boost of pressure with a bit of the crimp laying in the forcing cone.
    The 2-3/4 barrel may not have been proofed for 3" load pressure which is slightly higher than 2-3/4 proof, so don't say that I am saying 2-3/4 barrels are OK for 3" shells. I am saying the individual shell does not get a lot higher pressure from a different chamber length.

    EVERY manufacturer and SAAMI will tell you that you are to shoot how the barrel is marked and no longer than that.
    You should not expect them to tell you that shooting a longer shell is not a huge safety issue. Problems may arise when shooting a long 3" shell in an old loose and wobbly single shot, but that was foolhardy to use even with target loads.

    Did you ever wonder how a gun got to be so loose? It must have been shot well past the slight wiggle stage, and still didn't take off somebody's face. The barrel is still intact and not ruptured.
    Do you think that guns are really that easy to damage, with a tiny shell/chamber length difference?

    Guns, like many mechanical contrivances, are over-built for a safety factor. Recognize that link chains, for instance, have a working load about 20-25% of breaking load.

    You will also notice that I do not take into account any good or bad influence of a pattern with the shell being slightly longer than the chamber since this discourse is about safety.

    Winchester had a '97 taken off the assembly line and put into ammo testing service for well over 20 years and a definite million plus shells. They wanted to test pattern performance on a well-shot barrel, and that one still rated in a passing level for the full choke that it was marked, so, so much for shooting out a choke with lead shot. I'm sure that gun and barrel saw many high brass hunting and buckshot loads.

    I have spent much time conversing with personnel at Remington, from the last ammo plant manager, to corporate higher-ups, to the gun plant service manager. That guy has been Remington his whole career, and some of that time was in the testing area.
    That is where they don't see if a gun is hurt by a load, they find the load that blows the gun apart. Repeatedly. Talking to him is the next best thing to seeing the exploded residue for myself.
    When he says that pressure readings don't spike due to short chamber/long shell interference, that is a fact.

    There are enough circumstances that can make shooting a gun potentially hazardous without keeping another old wive's tale alive.

    Don't take a measurement of a chamber gauge being off 1/8" to get into a panic. I would not expect to use that as a money maker by playing on someone's fears. I do not mind a proper and exact chamber length, but shotguns are a lot different than rifles and throating conditions.
    Perfection is a great thing to have, and I will make things precise for somebody wanting that. I'm not going to exaggerate to get somebody worried enough to have something changed.

    If anybody pushes you to change one of these barrel examples for a safety reason by claiming a slightly short chamber is a grenade waiting to happen, ask them where their research lab is located or what other evidence they have.

    Damascus barrels blowing up from smokeless powder is another one of those old tales, at least from the time when both barrel types were in production.
    The loaders of the day could get bulk or dense smokeless powder.
    Bulk powder used the same powder dipper as the black powder, but the dense powder used a tiny powder dipper. What happens when they get mixed up? Triple charge?
    That must be the fault of the barrel, right?
    If you ever saw the test of a load of various damascus and fluid steel barrels being loaded to destruction, you would not think damascus was weak, any more.
    Some examples had so much powder and shot (well over 4 ounces for some, I believe) that the barrel was filled about half way. Some of the examples had actually welded the shot into a plug that failed to exit, and all the powder gas vented out of the fuse touch-hole. No ruptured barrel, in some instances, even at that extreme. Some of the best rated were damascus.
    I need to dig out the Double Gun Journal with that article inside.

    kirbythegunsmith@hotmail.com
endsnip---------------------------------------------------

BUT here is an opposing view from shotgun world
https://www.shotgunworld.com/bbs/viewtopic.php?f=2&t=471434

from Dustman47
snip--------------------------------------
A little straight talk on shot shells, shotgun chambers and forcing cones is needed to clear up some of the confusion and misinformation frequently posted on shotgun forums.

When talking about these things it is important to account for the era in which a shotgun was made as unfired and fired shell lengths and chamber length have varied through the years but have become more standardized in the last half century.

The fundamental anatomy of a shotgun barrel begins with the straight walled, cylindrical portion known as the chamber, in which a shot shell resides during firing. That is the portion denoted on the barrel and boxes of shot shells, as the chamber length and will be, 2 ¾”, 3” etc. Older shotguns may not have such notation. The chamber length is NOT the length of unfired shot shell but the length of a fired case that opens up into the straight wall chamber. When fired the casing opens up to release the shot and in doing so becomes longer, as opened, than it was closed. All shot shells are closed on the end by a crimp. Most all modern shells are closed with some type of star crimp but shells from older eras had simple rolled crimps with cardboard disc holding the shot in place. Rolled crimp shells open up shorter than star crimp shells of the same unfired length. The length of unfired case will vary a little among manufacturers by the type of crimping they use but thanks to the standardizing of “Sporting Arms and Ammunition Manufacturers Institute” (SAAMI) they will open up to their stated chamber length. Do not, on any gauge, be mislead because you can drop a 3” shot shell into the chamber of a 2 ¾” gun. An unfired 12 ga., 3” shell is only about 2 ¾” in length and will drop into the chamber of a 2 ¾” gun because the chamber is sized for an opened up shell case not a closed one. But, when fired a 3” shell opens up about another ¼”. Then there is no straight wall chamber length left in a 2 ¾” chamber to accept it and it has to open up into the smaller diameter of the forcing cone area of the barrel. That condition amounts to a constriction and leads to high barrel pressures that can be damaging to the gun and shooter.

Many older guns will have short chambers and were designed for a variety of chamber lengths as there were not always industry standards that now exist for modern shot shell and firearms manufacturers. Older guns can be re-chambered and their forcing cones lengthened to handle modern shells. Many shooters get away with it in older guns but shooting modern shells in an old gun chamber that was not designed for them is a bad practice. Many modern guns are designed to handle more than one shell length with some compromise in performance to handle different lengths.

Immediately following the straight wall cylindrical chamber there will be a conical section known as the forcing cone and there is no set length or angle of this section and it has varied significantly over time as shot shells have improved. The forcing cone will begin at the diameter or the chamber and reduce, over some short distance, to the bore diameter of the gauge shotgun it is. From there the barrel will be bore diameter to the muzzle where various size constrictions are applied known as choke. The intent of the forcing cone, before the near universal use of shot cups in shot shells was to force the mass of shot into a compact column coming down the barrel and minimize pressure gas leakage through and around the shot column. With modern shot cups the shot stays together inside the cup and the cup resists gas leakage until exiting the barrel. With shot cups the forcing cone doesn’t play its original role. However, one can still buy shot shells that don’t have shot cups and the forcing cone is still important for those shells.

endsnip----------------------------------

Now, with all that said, if it were me I would  only shoot "shorter" shells with rolled crimps.

I personally see no problem with using a shell that fits the chamber, and rolled crimps keep that extra plastic from increasing pressures:

Your Humble Servant
~~~~~Professor Algernon Horatio Ubiquitous Marvel The First~~~~~~
President, CEO, Chairman,  and Chief Bottle Washer of
Professor Marvel's
Traveling Apothecary
and
Fortune Telling Emporium


Acclaimed By The Crowned Heads of Europe
Purveyor of Patent Remedies, Snake Oil, Powder, Percussion Caps, Cleaning Supplies, Dry Goods,
and
Picture Postcards

Offering Unwanted Advice for All Occasions
and
Providing Useless Items to the Gentry
Since 1822
[
Available by Appointment for Lectures on Any Topic

Offline Professor Marvel

  • purveyor of useless items to the gentry
  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 2705
  • learn from the past, or be doomed to repeat it
  • Liked:
  • Likes Given: 329
Re: Winchester 1897 short chamber?
« Reply #3 on: November 15, 2020, 10:34:55 PM »
BTW since I have several pre-1900 doubles, one pre-1910 double, and a 1923 Marlin Model 1898, I literally am cutting some shells
"shorter" and using roll crimps.

I am marking the brass bases and heads with cold blue for easy identification even tho
They will function well in any 12 ga. but I like to seperate modernisch stuff from antiquey stuff  ;D

yhs
prof marvel
Your Humble Servant
~~~~~Professor Algernon Horatio Ubiquitous Marvel The First~~~~~~
President, CEO, Chairman,  and Chief Bottle Washer of
Professor Marvel's
Traveling Apothecary
and
Fortune Telling Emporium


Acclaimed By The Crowned Heads of Europe
Purveyor of Patent Remedies, Snake Oil, Powder, Percussion Caps, Cleaning Supplies, Dry Goods,
and
Picture Postcards

Offering Unwanted Advice for All Occasions
and
Providing Useless Items to the Gentry
Since 1822
[
Available by Appointment for Lectures on Any Topic

Offline Abilene

  • CAS-L Ghost Rider
  • Top Active Citizen
  • *
  • Posts: 3532
    • Abilene's CAS Pages
  • SASS #: 27489
  • NCOWS #: 3958
  • Liked:
  • Likes Given: 298
Re: Winchester 1897 short chamber?
« Reply #4 on: November 15, 2020, 10:37:56 PM »
Very interesting.  Keeps talking about safety and pattern but no mention of recoil reduction.  Mine is a solid frame 1914, and hadn't even thought about it.  Right now it is at a cowboy gunsmith getting ejection healthified.  I oughta have him check it.

Advertisers

  • Guest
Re: Winchester 1897 short chamber?
« Reply #5 on: Today at 08:08:25 AM »

Offline Professor Marvel

  • purveyor of useless items to the gentry
  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 2705
  • learn from the past, or be doomed to repeat it
  • Liked:
  • Likes Given: 329
Re: Winchester 1897 short chamber?
« Reply #5 on: November 15, 2020, 10:47:29 PM »
That's a good idea, Abilene!

here's another opinion from Lead Boolits
http://castboolits.gunloads.com/showthread.php?110940-Winchester-97-chamber-too-short

snip-----------------------------------------------------
I have opened up a lot of 97 & model 12 chambers in the past 30 years.

The "2 9/16" reamers hung around winchester much longer than they should have, and I have found M12's marked "2 3/4" with short chambers.

The big issue is a pressure spike. The folded crimp opens into the forcing cone, and then the wad gets shoved through the restriction. Hard on the gun & shooter both.

Reaming the 97 or M12 to at least 2 3/4 is a good plan. Running the 2 3/4 reamer to the barrel face on a takedown gun makes the chamber 2 3/4 + the thickness of the headspace ring - even better.
endsnip-----------------------------------------------------

apparently one can even check the chamber length with a dowel... I will totter out to the first ring of hell giant mess of hoarding workshop after the Grand Sumo Highlights Wrestling show and see what I can do....

prf marvel
Your Humble Servant
~~~~~Professor Algernon Horatio Ubiquitous Marvel The First~~~~~~
President, CEO, Chairman,  and Chief Bottle Washer of
Professor Marvel's
Traveling Apothecary
and
Fortune Telling Emporium


Acclaimed By The Crowned Heads of Europe
Purveyor of Patent Remedies, Snake Oil, Powder, Percussion Caps, Cleaning Supplies, Dry Goods,
and
Picture Postcards

Offering Unwanted Advice for All Occasions
and
Providing Useless Items to the Gentry
Since 1822
[
Available by Appointment for Lectures on Any Topic

Offline Coffinmaker

  • Top Active Citizen
  • *
  • Posts: 6449
  • Liked:
  • Likes Given: 72
Re: Winchester 1897 short chamber?
« Reply #6 on: November 16, 2020, 09:22:27 AM »

 :)  Dirty Dick & Our Good Perfesser.  :D

I am amazed.  Anyone whom can claim there is no pressure spike (first Ex Spert) with a 2 3/4 round in a 2 9/16 chamber is a quack.  Not to mention the close proximity of the forcing cone.  There is, in fact, a distinct and detectable pressure spike.

It was my practice, to check the chamber on ALL older guns.  There is no way a wad can be shoved thru a restricted chamber, then into a restricted forcing cone and not have a pressure spike.  After checking the chamber dimension, I reamed the chamber to 2 3/4+ AND lengthened the forcing cone.  The shooter will notice an appreciable reduction in felt recoil.  The elimination of the pressure spike is also good for the gun.

then we have the same (Ex-Spert) touting the safety of Damascus barrels.  Would that I could, I would reach through and choke the living crap out of the Marooon.  Let is remember please, An "Ex" is a has-been, and a "Spert" is merely a Drip under Pressure.  Burma Shave!!

I am NOT Opinionated.  So There.

Offline Professor Marvel

  • purveyor of useless items to the gentry
  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 2705
  • learn from the past, or be doomed to repeat it
  • Liked:
  • Likes Given: 329
Re: Winchester 1897 short chamber?
« Reply #7 on: November 16, 2020, 09:22:11 PM »
Thanks for the reply, Coffin!!!

I could not imagine how extra shell petals in the forcing cone would not increase pressure!
Nor could I wrap my head around "Incresed kick" without increased pressure...

yup, if it's on the interwebs... one takes one's chances!

I still need to go check my chambers with a stick.

yhs
prof marbles
Your Humble Servant
~~~~~Professor Algernon Horatio Ubiquitous Marvel The First~~~~~~
President, CEO, Chairman,  and Chief Bottle Washer of
Professor Marvel's
Traveling Apothecary
and
Fortune Telling Emporium


Acclaimed By The Crowned Heads of Europe
Purveyor of Patent Remedies, Snake Oil, Powder, Percussion Caps, Cleaning Supplies, Dry Goods,
and
Picture Postcards

Offering Unwanted Advice for All Occasions
and
Providing Useless Items to the Gentry
Since 1822
[
Available by Appointment for Lectures on Any Topic

Offline Dirty Dick

  • Top Active Citizen
  • *
  • Posts: 136
  • Liked:
  • Likes Given: 15
Re: Winchester 1897 short chamber?
« Reply #8 on: November 17, 2020, 05:46:14 AM »
About ten years ago I saw an 1897 Winchester with a damascus barrel at a dealers gun rack, the shop person said many Winchester '97s were so made, is this true? It had a very pretty pattern and the price was not bad but I am leary of damascus barrels as I have a very old Cape gun, shotgun/rifle side by side with the rifle barrel burst right where the shooters left thumb would be if he were right handed. My father brought it home one day said a customer had given it to him because he knew I liked guns. It is really a piece of junk, only one lock remains of what looks like a percussion double. There are no marking I can make out, no provenance and no other details. I also have taped to my Dillon 1050 as a reminder the burst inner primer magazine tube that is the result of a primer magazine detonation, a full tube of Federal large pistol primers went up just as I had my face very close to the primer shuttle bar to clear a jam. I was not wearing eye protection at the time and was extremely lucky to get only a very small nick in the corner of one eye. Thank you Mike Dillon for the design of my machine! Anyhoo, whenever I see a damascus barrel I picture this old cape gun and imagine myself without a left thumb/ hand/eyes and decide not to tempt fate.

Just my $0.02
NRA Life, CSSA, RCA,

Offline Coffinmaker

  • Top Active Citizen
  • *
  • Posts: 6449
  • Liked:
  • Likes Given: 72
Re: Winchester 1897 short chamber?
« Reply #9 on: November 17, 2020, 09:19:11 AM »

I know early Winchester '97s were made with Damascus barrels.  There were folks in those early years, whom didn't trust fluid steel barrels and ordered their guns specifically with Damascus.

Today, I wouldn't shoot a Damascus gun for any price.  I value my mother nature given parts way too much.

Advertisers

  • Guest
Re: Winchester 1897 short chamber?
« Reply #10 on: Today at 08:08:25 AM »

Offline Sir Charles deMouton-Black

  • THE ANCIENT SUBSTANCE ENDURES - ALL LESSER PROPELLANTS SHALL FIZZLE
  • NCOWS Member
  • Top Active Citizen
  • ***
  • Posts: 6100
  • Liked:
  • Likes Given: 105
Re: Winchester 1897 short chamber?
« Reply #10 on: November 18, 2020, 10:40:34 AM »
I have three '97s. The first was an expensive lesson in purchasing gunparts. Nuff said, I did use the full choke barrel as a spare for one of the others. The last two I purchased as twofer while sitting together with the owner enjoying his hospitality and the view of Lac La Hache BC. The best one was a 1953 (Second last year of manufacture with all improvements and Model 12 wood) and it helped win one of my best matches ever. The last was a 1908 shortened for a Weaver "Dial-a-duck" choke.  I had the barrel bobbed to 22" and a thin-wall choke installed, 'though I often shot it with the 30" full choke barrel. It became my go-to gun until I went to hammer doubles and BP all 'round.

Out it came when I shot my first Wild Bunch, match rigged for a six shot "run". The 97 could only make five, but I didn't want to change it or buy an expensive after-market spring. I had been experimenting with short shells, down to AAs cut off to 2" and roll crimped, so I tried 'em in the old corn-shucker. Whoopee, I could get that extra shell in!

Then, I tried working the action! Those shells got lost in that big dark hole between Mag and Mouth!
 
After the traditional research process - Cut 'n try, I found the sweet spot. Cut an AA split-neck to 2 3/8 inch and roll crimp over a suitable wad column , I think it was an AA red-wad, roll crimp and Roberts yer Fathers Brother.
NCOWS #1154, SCORRS, STORM, BROW, 1860 Henry, Dirty Rat 502, CHINOOK COUNTRY
THE SUBLYME & HOLY ORDER OF THE SOOT (SHOTS)
Those who are no longer ignorant of History may relive it,
without the Blood, Sweat, and Tears.
With apologies to George Santayana & W. S. Churchill

"As Mark Twain once put it, “History doesn’t repeat itself, but it does rhyme.”

 

SMF spam blocked by CleanTalk

© 1995 - 2020 CAScity.com