Author Topic: High Shooter  (Read 354 times)

Offline Doubles

  • Citizen
  • *
  • Posts: 2
  • Liked:
  • Likes Given: 0
High Shooter
« on: December 03, 2020, 10:33:56 AM »
Well, I mosseed on over an picked me up a new pea-shooter - found an EMF New Dakota, 45, 43/4” made by ASM. The dang thing is nickel plated too! Heck, I look like the original Pimp Cowboy with it.  But don’t cha know the darn thing shoots high. Not a little high. We’re takin like a foot at 9 yards. Firing a 255 over 7gr. Of Unique.   So, Ole Buddys, might ya have any words of wisdom fer me as to how I may rectify this situation?  Ain’t no prude, so smart-face responses welcomed also. 

Offline Cap'n Redneck

  • Commd'g Co. D, Frontier Batt'n, Texas Rangers.
  • Very Active Citizen
  • *
  • Posts: 71
  • Cap'n Redneck SWS #163.
  • Liked:
  • Likes Given: 0
Re: High Shooter
« Reply #1 on: December 03, 2020, 11:22:22 AM »
Quick-fix #1:  Always aim 12 inches below Your intended target.   

Quick-fix #2:  Get a piece of brass-shim, fold it in half, glue the shim to Your frontsight.
(the folded shim should sit on the frontsight like a saddle sits on a skinny hoss, if'n You get my drift?)

You probably don't want to use too much heat and solder, in fear of ruining the nickel plating.

"As long as there's lead in the air, there's still hope..."
Frontiersman & Frontiersman Gunfighter: The only two categories where you can play with your balls and shoot your wad while tweaking the nipples on a pair of 44s.

Offline August

  • Deputy Marshal
  • Top Active Citizen
  • *
  • Posts: 586
  • Liked:
  • Likes Given: 3
Re: High Shooter
« Reply #2 on: December 03, 2020, 11:26:56 AM »
I'd first try to determine what load it was regulated for and then decide if that load meets your personal intentions for use of the gun.  If that load does't meet your purposes, I'd say it is gunsmith time to begin again with a full-height sight.

Offline Doubles

  • Citizen
  • *
  • Posts: 2
  • Liked:
  • Likes Given: 0
Re: High Shooter
« Reply #3 on: December 03, 2020, 04:13:57 PM »
Thank you fellas. I believe the only way that pistola is not going to shoot high is if I pull the bullet outta the barrel with a string. I lied about how high it shoots. Was more like 2 feet. Front sight modification warranted.

Would you recon this ta be a common problem, i.e. with the Cimarrons?.

Offline Jubal Starbuck

  • Top Active Citizen
  • *
  • Posts: 212
  • Liked:
  • Likes Given: 0
Re: High Shooter
« Reply #4 on: December 03, 2020, 05:53:14 PM »
    You might try loading some lighter weight bullets.  A 225 to 230 grain slug should lower your point of impact some.

Advertisers

  • Guest
Re: High Shooter
« Reply #5 on: Today at 08:58:18 AM »

Offline Abilene

  • CAS-L Ghost Rider
  • Top Active Citizen
  • *
  • Posts: 3464
    • Abilene's CAS Pages
  • SASS #: 27489
  • NCOWS #: 3958
  • Liked:
  • Likes Given: 257
Re: High Shooter
« Reply #5 on: December 03, 2020, 07:57:28 PM »
And a 200 grain bullet will print lower still.  What is your sight picture?  Top of front sight even with rear sight?  It is common for these guns to shoot high with 250 gr bullets  as they were originally regulated to be on target at something like 75 or 100 yards.  But I would say that 2 feet high at 9 yards is excessive and not common with any SAA's.

 

SMF spam blocked by CleanTalk

© 1995 - 2020 CAScity.com