Author Topic: Bullseye ejector rods for a Vaquero  (Read 1641 times)

Offline DeaconKC

  • Retired Predator Hunter
  • Top Active Citizen
  • *
  • Posts: 556
  • Liked:
  • Likes Given: 0
Bullseye ejector rods for a Vaquero
« on: June 22, 2019, 06:42:59 am »
I seem to recall an aftermarket maker that offered bullseye style ejector rods for Vaqueros some years back. I cannot find any listing for them today. Am I dreaming or are they still out there?
Yup, I'm that DeaconKC from Surplus Rifle
The Deacon AZSA
BOLD 1088

Offline King Medallion

  • Top Active Citizen
  • *
  • Posts: 661
  • Liked:
  • Likes Given: 1
Re: Bullseye ejector rods for a Vaquero
« Reply #1 on: June 22, 2019, 08:36:58 am »

Offline Jubal Starbuck

  • Top Active Citizen
  • *
  • Posts: 210
  • Liked:
  • Likes Given: 0
Re: Bullseye ejector rods for a Vaquero
« Reply #2 on: June 22, 2019, 08:40:47 am »
     I bought some from Brownell's some years ago.

Offline DeaconKC

  • Retired Predator Hunter
  • Top Active Citizen
  • *
  • Posts: 556
  • Liked:
  • Likes Given: 0
Re: Bullseye ejector rods for a Vaquero
« Reply #3 on: June 22, 2019, 09:44:22 am »
 ;D King, thank you kindly Sir! My googlefu didn't pull that up!
Yup, I'm that DeaconKC from Surplus Rifle
The Deacon AZSA
BOLD 1088

Offline Chev. William

  • Top Active Citizen
  • *
  • Posts: 492
  • Liked:
  • Likes Given: 0
Re: Bullseye ejector rods for a Vaquero
« Reply #4 on: July 04, 2019, 10:20:42 am »
Thanks for bringing this to my attention,  I bought a pair for my two Ruger Single Six/Eight convertibles to make ejecting empties easier for me.

Chev. William
"Been there, But no 'Tee Shirt' survived.

Offline Coffinmaker

  • Top Active Citizen
  • *
  • Posts: 5964
  • Liked:
  • Likes Given: 25
Re: Bullseye ejector rods for a Vaquero
« Reply #5 on: July 05, 2019, 01:11:13 pm »

Oops.  I forgot to jump in here and relate, Brownells still offer the Colt style Crescent Ruger Ejector rod from MK Technologies.  I much prefer the crescent myself.

A CAVEAT:  Some find it objectionable that the MK Technologies crescent rod REQUIRES fitting.  It is too fat for the slot in the housing and must be reduced for proper fit and perhaps polished for smooth operation.


Offline Mustang Gregg

  • .44 BP GUNFIGHTER
  • Deputy Marshal
  • Top Active Citizen
  • *
  • Posts: 1971
  • LtCol Mustang Gregg & Col Pitspitr at NE CSG 2007
    • Wild West Arms
  • Liked:
  • Likes Given: 0
Re: Bullseye ejector rods for a Vaquero
« Reply #6 on: August 14, 2019, 04:51:51 pm »
Thanks, King!
You beat me to it.

MG
"I have two guns.  {CLICK--CLICK}  One for each of ya."
  BACK FROM AFGHANISTAN!!
"Mustang Gregg" Clement-----NRA LIFER, since '72-----SASS Life & Territorial Governor-----GAF #64-----RATS #0 & Forum Moderator-----BP Warthog------Distinguished Pistol 2004------SAIROC & MMTC Instructor-----Owner of Wild West Arms, Inc. [gun shop] Table Rock, NE------CASTIN' & BLASTIN'!!!!
www.wildwestarms.net

Offline Crow Choker

  • Top Active Citizen
  • *
  • Posts: 952
  • River Banker Extraordinaire
  • Liked:
  • Likes Given: 4
Re: Bullseye ejector rods for a Vaquero
« Reply #7 on: October 03, 2019, 08:01:22 am »
I'm late for the party on this one, but the MK ejector I bought for my old model Rug Vac I got from Brownells probably a dozen years ago works good. As CM advised it did need a bit of fitting, but nothing real intensive. I changed it not so much that it wasn't the dreaded 'not period correct', but the original had to small of a head.. I went with the crescent as I didn't care for the looks of the larger bullseye. It looked to large, out of place.
Darksider-1911 Shooter-BOLD Chambers-RATS-SCORRS-STORM-1860 Henry(1866)-Colt Handgun Lover an' Fan-NRA-"RiverRat"-Conservative American Patriot and Former Keeper & Enforcer of the Law an' Proud of Being Both! >oo

 

SMF spam blocked by CleanTalk
© 1995 - 2020 CAScity.com