Author Topic: Looking for a Case Gage for .44-40  (Read 7267 times)

1972

  • Guest
Looking for a Case Gage for .44-40
« on: December 22, 2014, 02:39:31 PM »
I’m looking for a case gage for .44-40 to serve as a check when re-loading.

These are the gages machined out of a solid piece of steel to duplicate a chamber meeting SAAMI specs for any given particular caliber.  You drop a loaded round in and the gage will measure/check the maximum dimensions – including case length, width, case diameter, max cartridge dimensions, and max length of the loaded round.  That sort of thing.  The bottom line is if it fits the gage then you know it meets SAAMI specs and should fit in any firearms chambered for that cartridge.

I have such gages (L.E. Wilson) for my 45 ACP and 45 Colt but they (L.E. Wilson) don’t offer one for .44-40 WCF.  Dillon does not offer that one either.

Does anybody know of some manufacturer who makes such a gage for .44-40?  I could use the chamber of one of my firearms in that caliber but I’d much rather have an actual gage.

Any suggestions would be appreciated.

Thanks fellas - and Merry Christmas to all of you and your families

Offline cpt dan blodgett

  • Top Active Citizen
  • *
  • Posts: 1693
  • SASS Conv 2013
  • Liked:
  • Likes Given: 3
Queen of Battle - "Follow Me"
NRA Life
DAV Life
ROI, ROII

1972

  • Guest
Re: Looking for a Case Gage for .44-40
« Reply #2 on: December 22, 2014, 03:21:45 PM »
like this one at midway usa?
http://www.midwayusa.com/product/266798/le-wilson-case-length-headspace-gage-44-40-wcf

I asked Wilson about that.  That particular model only checks case length to determine head space.  It's better than nothing, but I wanted the one that checks the entire loaded cartridge so you know if the re-loaded round fits the gage - it will fit any firearm chambered to SAAMI specs.

Wilson makes the total gage for most pistol calibers, but not for 44-40.  I asked them if they could make me one and they said they didn't have the reamer for that cartridge.

Advertising

  • Guest
Re: Looking for a Case Gage for .44-40
« Reply #3 on: Today at 09:32:48 AM »

Offline Jubal Starbuck

  • Top Active Citizen
  • *
  • Posts: 231
  • Liked:
  • Likes Given: 1
Re: Looking for a Case Gage for .44-40
« Reply #3 on: December 22, 2014, 05:08:48 PM »
      I'm not sure this is what you are looking for, but I  will tell you how I have done it for cartridges to be used in 5 revolvers and four rifles in .44-40.  I simply remove a cylinder from one of my revolvers and drop each loaded round into it.  This  method has always worked for me.  I adjusted my dies so the loaded rounds fall in and back out.  It doesn't take long to do, either.
   Hope this helps.

   Jubal Starbuck

Offline Abilene

  • CAS-L Ghost Rider
  • Top Active Citizen
  • *
  • Posts: 4672
    • Abilene's CAS Pages
  • SASS #: 27489
  • NCOWS #: 3958
  • Liked:
  • Likes Given: 1181
Re: Looking for a Case Gage for .44-40
« Reply #4 on: December 22, 2014, 05:22:26 PM »
      I'm not sure this is what you are looking for, but I  will tell you how I have done it for cartridges to be used in 5 revolvers and four rifles in .44-40.  I simply remove a cylinder from one of my revolvers and drop each loaded round into it.  This  method has always worked for me.  I adjusted my dies so the loaded rounds fall in and back out.  It doesn't take long to do, either.
   Hope this helps.

   Jubal Starbuck

I do the same, though I only have one rifle and one pistol in 44-40.  Both are Ubertis with their typically tight chambers.  I mostly shoot the rifle, but if the rounds fit the cylinder then I know they are fine in the rifle.

1972

  • Guest
Re: Looking for a Case Gage for .44-40
« Reply #5 on: December 24, 2014, 10:38:20 AM »
Thanks Jubal.  That's what I will probably end up doing.  I was just hoping to find a gage, but it's not the end of the world. Given the growth of popularity with the 44-40 again (due to CAS) you'd think somebody would be offering one.

Offline Sir Charles deMouton-Black

  • THE ANCIENT SUBSTANCE ENDURES - ALL LESSER PROPELLANTS SHALL FIZZLE
  • NCOWS Member
  • Top Active Citizen
  • ***
  • Posts: 6199
  • Liked:
  • Likes Given: 396
Re: Looking for a Case Gage for .44-40
« Reply #6 on: December 24, 2014, 06:06:13 PM »
Get a digital caliper. Probably Harbor Freight has the best price.   (In Canada, go to Princess Auto.)

You will never use a case gauge again. 8)
NCOWS #1154, SCORRS, STORM, BROW, 1860 Henry, Dirty Rat 502, CHINOOK COUNTRY
THE SUBLYME & HOLY ORDER OF THE SOOT (SHOTS)
Those who are no longer ignorant of History may relive it,
without the Blood, Sweat, and Tears.
With apologies to George Santayana & W. S. Churchill

"As Mark Twain once put it, “History doesn’t repeat itself, but it does rhyme.”

Offline longinosoap

  • Very Active Citizen
  • *
  • Posts: 90
  • Liked:
  • Likes Given: 0
Re: Looking for a Case Gage for .44-40
« Reply #7 on: January 28, 2015, 08:06:55 AM »
This what you're looking for?

ftp://

Offline Fingers McGee

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 1397
  • Smoke & Fire
  • SASS #: R28654
  • NCOWS #: 3638
  • Liked:
  • Likes Given: 6
Fingers (Show Me MO smoke) McGee;
SASS Regulator 28654 - L - TG; NCOWS 3638
AKA Man of many Colts; Diabolical Ken's alter ego; stage writer extraordinaire; Frontiersman/Pistoleer; Rangemaster
Founding Member - Central Ozarks Western Shooters
Member - Southern Missouri Rangers;
NRA Patron Life: GOA; CCRKBA; SAF; SV-114 (CWO4 ret); STORM 327

"Cynic:  A blackguard whose faulty vision sees thing as they are, not as they should be"  Ambrose Bierce

Offline cheatin charlie

  • Top Active Citizen
  • *
  • Posts: 103
  • Liked:
  • Likes Given: 0
Re: Looking for a Case Gage for .44-40
« Reply #9 on: January 29, 2015, 07:12:21 AM »

1972

  • Guest
Re: Looking for a Case Gage for .44-40
« Reply #10 on: February 18, 2015, 06:36:43 PM »
Thanks guys.  Yep, that's what I was looking for.  Thanks.  Sorry I didn't get back to you sooner but have been away working.

 

SMF spam blocked by CleanTalk

© 1995 - 2023 CAScity.com