Author Topic: Black Powder in the 44-40  (Read 75482 times)

Offline Fox Creek Kid

  • Top Active Citizen
  • *
  • Posts: 4508
Re: Black Powder in the 44-40
« Reply #50 on: February 19, 2012, 10:30:55 pm »
6" is not enough of a drop to get the best BP stacking. Minimum is 18" and anything over 3' is a waste. There was a test years ago on this on another forum and this was the conclusion drawn. I think if you re-do your loads you might get better results.  ;)

Offline w44wcf

  • Top Active Citizen
  • *
  • Posts: 1148
Re: Black Powder in the 44-40
« Reply #51 on: February 20, 2012, 07:20:28 am »
David,
Thank you for the range report.  The most accurate bullet for me shooting b.p. in the 44-40 with Swiss powder is  the 427098.
Montana Bullet Works offers the 427098 in .429" diameter with b.p. lube (specify at the time of order)
It is the 2nd one down this page.....
http://www.montanabulletworks.com/44_40.html

With Swiss, the lesser lube capacity is not an issue, I've run 50+ rounds with accuracy being maintained throughout and the muzzle has a lube ring.



If you send me a PM  with your address, I could send you 20 or so bullets to try to see how they would work before you ordered any.

Here's a couple of targets.....




w44wcf
« Last Edit: February 20, 2012, 05:57:48 pm by w44wcf »
aka Jack Christian SASS 11993 "I can do all things through Christ who strengthens me." Philippians 4:13
aka John Kort
aka w30wcf (smokeless)
NRA Life Member
.22 W.C.F., .30 W.C.F., .44 W.C.F., .45 Colt Cartridge Historian

Offline David Battersby

  • Active citizen
  • *
  • Posts: 42
  • Smokeless powder is a passing fad .
Re: Black Powder in the 44-40
« Reply #52 on: February 22, 2012, 04:59:40 pm »
   John
      I have ordered the 42798 bullets and an RCBS design that looks similar. I will shoot both and let you know. I need to get my hands on a pound of Swiss FFG. What are your thoughts on Walters Wads under the bullet for a reduced charge of Swiss FFFG ?
Just an idea to try if I get the bullets before the powder.

      Thanks
      David
John Moses Browning and Teddy Roosevelt, we need you again !
In the days of old when men were bold and a quarter was still worth a dime.

Offline w44wcf

  • Top Active Citizen
  • *
  • Posts: 1148
Re: Black Powder in the 44-40
« Reply #53 on: February 24, 2012, 07:56:47 am »
David,
I have never used a base wad but I think that since it is used as a bullet extension to compress a lesser powder charge it would work aok.

Regarding Swiss, the Back Creek Gun Shop  http://blackpowderva.com/  does not have a minimum purchase as far a I know but there is a hazmat fee of $25 per order.

Hope that it all comes together for you.

w44wcf
aka Jack Christian SASS 11993 "I can do all things through Christ who strengthens me." Philippians 4:13
aka John Kort
aka w30wcf (smokeless)
NRA Life Member
.22 W.C.F., .30 W.C.F., .44 W.C.F., .45 Colt Cartridge Historian

Offline Kinchafoonee Kid

  • Kinchafoonee Kid
  • NCOWS
  • Very Active Citizen
  • ***
  • Posts: 82
Re: Black Powder in the 44-40
« Reply #54 on: May 09, 2012, 09:01:32 pm »
Good evening, everyone. I have an Uberti 1873 44 WCF 30 in barrel. I load using Starline brass, cci magnum primers, 35 gr Schuetzen 2f, Accurate mould bullet in .428' no wad, using homemade DanT lube recipe.  I recently shot two CAS matches 50 rounds each, hitting all rifle targets with no misses.  No cleaning during the match.  A greasy ring on my muzzle.  I look forward to reporting some actual testing at the range, will post further experimentation.  Thanks to 44wcf for suggesting the accurate mould.

KK
Kinchafoonee Kid
SSAS 94231

Offline w44wcf

  • Top Active Citizen
  • *
  • Posts: 1148
Re: Black Powder in the 44-40
« Reply #55 on: May 10, 2012, 04:36:24 pm »
Kinchafoonee Kid,
Thank you for the report. Nice shooting!  ;D ;D  
Glad to hear that the 43-215C is working well in your 30" barrel.  ;D

w44wcf
aka Jack Christian SASS 11993 "I can do all things through Christ who strengthens me." Philippians 4:13
aka John Kort
aka w30wcf (smokeless)
NRA Life Member
.22 W.C.F., .30 W.C.F., .44 W.C.F., .45 Colt Cartridge Historian

Offline Kinchafoonee Kid

  • Kinchafoonee Kid
  • NCOWS
  • Very Active Citizen
  • ***
  • Posts: 82
Re: Black Powder in the 44-40
« Reply #56 on: May 11, 2012, 11:38:43 pm »
W44wcf, thanks agai for your age advice and wisdom.

KK
Kinchafoonee Kid
SSAS 94231

Offline David Battersby

  • Active citizen
  • *
  • Posts: 42
  • Smokeless powder is a passing fad .
Re: Black Powder in the 44-40
« Reply #57 on: June 11, 2012, 10:30:40 am »

          W44wcf
               I know it has been a while, spring and summer are crazy busy for me, so here is an update. If I attached the image correctly you will see my best result of my first Swiss/427098 test. I was shooting at 100 yards on a warm dry day, front sandbag rest holding rear of rifle. This was the Montanna Bullet works 427098 with 2.18cc of Swiss 1.5F.  Two other loads of more powder and two with the RCBS 200gr bullet were larger groups. I did get leading just ahead of the chamber when I shot this load Saturday @ Atglen. With the match, sighting in and playing that was sixty rounds. I did clean the rifle after the first twnty rounds, just to see and feel the fouling. I noticed that when sitting while the other relay was shooting the bore near the muzzle would start to appear "dry". I began using a blow tube before and after each relay without cleaning. The dry/chalky area would moisten very quickly. ( Using the blow tube amused Jack and Gunny , ALOT ) My score was close to what I average in the Pistol Caliber game and it was alot of fun. I will get more bullets and work on fine tuning a load, as I also got a couple pounds of Swiss 2F.
  A couple things I noticed. The loads with more powder had heavier thicker fouling. Again, even the most accurate load is leading just ahead of the chamber. The leading I believe is do to bullet fit and alloy. The bullets are .429 and the bore is .429 plus the bullets are Lyman#2 Alloy, not 20-1. Just a little too small and too hard to seal the bore . At least that is my guess. 
  I will post new results, just don't hold your breath. This is the wrong time of the year for load developement. I will say this though, not matter how busy I am, silhouette matches are on the calender. Like a doctor's appointment they can not be missed.

           David

           P.S. If you talk to them, give Jack and Gunny my love!! ;D
John Moses Browning and Teddy Roosevelt, we need you again !
In the days of old when men were bold and a quarter was still worth a dime.

Offline w44wcf

  • Top Active Citizen
  • *
  • Posts: 1148
Re: Black Powder in the 44-40
« Reply #58 on: June 12, 2012, 08:58:20 am »
David,
Thank you for the range report.  Glad to see that you are making good progress!   
Looks like the majority of the bullets impacted in 3" with almost all in 4" @ 100.  ;D ;D

If the bullets are 15 BHN as advertised and they were .002" over groove diameter, the throat leading should cease.

My normal b.p. bullets are 10-12 bhn but I have fired 16 BHN bullets that were .002" over groove and they shot very well with no leading. ;D

I could "bump up" some of your bullets to .431" if you send me some.  I'll send you an email about that.

Hopefully, I'll see Sixgun & Gunny at the Regional Cowboy Silhouette Championship in Bradford.......

w44wcf

 
« Last Edit: June 12, 2012, 09:02:26 am by w44wcf »
aka Jack Christian SASS 11993 "I can do all things through Christ who strengthens me." Philippians 4:13
aka John Kort
aka w30wcf (smokeless)
NRA Life Member
.22 W.C.F., .30 W.C.F., .44 W.C.F., .45 Colt Cartridge Historian

Offline David Battersby

  • Active citizen
  • *
  • Posts: 42
  • Smokeless powder is a passing fad .
Black Powder in the 44-40
« Reply #59 on: July 01, 2012, 08:19:56 am »
    
    John
       Again, summer is a crazy busy time for me . Here is an update.
       The attached photo is of two bullet designs I just received. They are at bore diameter as the last bullets tried , BUT are cast with a 30-to-1 alloy . They are from Mt Badly Bullets. They are not listed on the web site but are available. I e-mailed them and as advertised Frank called me back and let me know what they had and could do. If the bullets are half as good as their customer service then X-rings are in my future.  I am going to load some trial ammo with Swiss 1.5F and 2F.  On the Lyman 427098 I will try crimping lightly just ahead of the first driving band. The idea is to have the bullet seated on the powder and have a crimp that will not distort the bullet in any way.  I tried seating the bullet with the first drive band flush with the case mouth, but the O.A.L. is too long for my rifle. I will post a range report when I get the time to go to the range.

                David

P.S. As much as I wanted too there was no way to make the Eastern Regional match. Next year I will plan for it much sooner.
John Moses Browning and Teddy Roosevelt, we need you again !
In the days of old when men were bold and a quarter was still worth a dime.

Offline w44wcf

  • Top Active Citizen
  • *
  • Posts: 1148
Re: Black Powder in the 44-40
« Reply #60 on: July 02, 2012, 07:39:39 am »
David,
Thank you for the update. For the very best performance (groups), I would shoot only those bullets that had no visible defects, especially on the base, and that did not vary more than + - .3 grs. in weight.

I'll look forward to your future range report(s).

I did not make it to the Eastern Regional match either ...... family doings.  So, I am looking forward to the PA State Match Sep1 and Sep2 in Ridgway......

w44wcf

aka Jack Christian SASS 11993 "I can do all things through Christ who strengthens me." Philippians 4:13
aka John Kort
aka w30wcf (smokeless)
NRA Life Member
.22 W.C.F., .30 W.C.F., .44 W.C.F., .45 Colt Cartridge Historian

Offline Jubal Wilson

  • American Plainsmen Society
  • Very Active Citizen
  • *
  • Posts: 63
Re: Black Powder in the 44-40
« Reply #61 on: December 13, 2012, 11:57:20 pm »
w44wcf/John, it has been a bad year for me as far as shooting. Since we had such a dry year I haven't been able to get out to the forest (closed because of extreme fire danger) since my last post on this thread. Anyway I have a question for you. Have you tried a side by side comparison of the accuracy of the 427098 and the 43-215C using the same load of Swiss? It seems to me that the wide lube groove would effect the streamlining of the bullet when it spun off the lube. I am talking about 200 to 300 yards.
We are still waiting on our new rifle range but the Game, Fish and Parks which took over the project says maybe by summer. It sure will be nice.
Jubal/Paul
Jubal Wilson

When a man loses his dreams he becomes a wanderer in the wasteland of human existence.

Offline 58cal

  • Citizen
  • *
  • Posts: 22
Re: Black Powder in the 44-40
« Reply #62 on: December 14, 2012, 05:34:48 am »
Good morning....I really appreciate this forum. I'm learning a lot.

In the North-South Skirmish Association, we have a breech loading rifle competition.
Most competitors use Uberti Henry rifles in mostly 44WCF. Spencer's are less common.
A commonly used bullet that isn't discussed much in this forum is the Lyman 429667,
weighing close to 250 grains(in hardball)...715 inches long.

Happy Holidays!

58cal
Charleston, SC




Offline David Battersby

  • Active citizen
  • *
  • Posts: 42
  • Smokeless powder is a passing fad .
Re: Black Powder in the 44-40
« Reply #63 on: December 29, 2012, 01:08:27 pm »
 Merry Christmas and Happy New Year

   I have been working on my black powder loads for my Uberti 1873 in 44-40 and I guess there is progress to share and a question or two.
 I had some encouraging results from the last batch of cast bullets purchased, but they were also the most expensive cast bullets purchased. So now I am a bullet casting...um...uh..fellow.  I have a Lee 20lb bottom pour pot with basic accessories. I chose the Accurate 43-220C as it follows the original Lyman nose profile, is flat based and with smokeless loads my rifle has done better with 240 grain bullets.
 My first and only batch of bullets so far were not perfect. Many have wrinkled lines in the noses. I cleaned the mold with denatured alcohol, smoked the cavities with a butane lighter and lubed the alignment pins with graphite. I believe I simply did not get the mold hot enough . I have since recleaned the mold with brake cleaner. Should I smoke the cavities ? Should I hold the sprue plate against the spout when pouring, or leave a small air gap ?  I will try again and report back.
  As of right now I am casting 30-to-1 alloy. The bullets that look good are round, uniform in weight and are .431in diameter as cast, which is what I requested.  The bore is .429 just ahead of the chamber. The bullets have good neck tension in unresized fired cases. The cartridge loads into the rifle chamber with no problems.
 I also have a powder compression die now. Compressing the powder with bullet seating most definitely squashes those soft bullets. I am using DGL bullet lube. It is a soft black powder lube similar to SPG but more oily. Pan lubed not sized.
 The combination of the above has been impressive. After 50 rounds fired there is a substantial grease ring on the muzzel and the thinnest softest fouling I have experienced in the bore. Today I shot one of the best 100 yard groups ever with this rifle, with ANY load.
 My best black powder load so far has been with Swiss 1.5f, which gave me a couple surprises and raised a few questions. I have tried 2.45cc of Swiss 2f which weighs 35.2 grains and is compressed 1/8 inch. The seated bullet touching the compressed powder. The accuracy was good but I loaded another box of 50 to compare with any other combinations I might try. While all the equipment and components were out I loaded a box with 2.45cc of 1.5f . I was surprised as this weighs 37 grains. I was expecting a bulkier powder of the same volume to weigh less . As I fired this load I observed more "sparks/flares" falling out of the muzzel as compared to the 2f load. I was sure this was due to inefficient combustion and would be an inaccurate load. Well look at the picture and you tell me. The seventeen holes are the first 10 after fouling shots and then the last seven out of a box of 50. The target is torn up because it was wet when I pulled it down, as it started raining. Visibility went south , I could hardly see the bright white bullseye and yet....wow !
 I will try again compairing 1.5f and 2f Swiss before I order a case, but I am curious. Has anyone else compaired them and found one better in the 44-40 ? I know every rifle is a creature to itself, just curious. As I stated the loads were compressed about 1/8in, would more or less powder be better ?
« Last Edit: December 30, 2012, 05:47:36 am by David Battersby »
John Moses Browning and Teddy Roosevelt, we need you again !
In the days of old when men were bold and a quarter was still worth a dime.

Offline wildman1

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 2723
Re: Black Powder in the 44-40
« Reply #64 on: December 30, 2012, 06:22:35 am »
I also have a 20 lb Lee pot. When I pour the larger bullets I use a Lyman ladle because I also had trouble with imperfect bullets from the bottom spout on the Lee pot, doesn't get the lead in the mold fast enough. Same temp using the Lyman Ladle but the bullets come out perfect. The Lee bottom pour works great on the smaller bullets. WM
« Last Edit: December 30, 2012, 07:33:17 pm by wildman1 »
WARTHOG, Dirty Rat #600, BOLD #1056, CGCS,GCSAA, NMLRA, NRA, AF&AM, CBBRC.  If all that cowboy has ever seen is a stockdam, he ain't gonna believe ya when ya tell him about whales.

Offline w44wcf

  • Top Active Citizen
  • *
  • Posts: 1148
Re: Black Powder in the 44-40
« Reply #65 on: December 30, 2012, 10:07:59 am »
........Have you tried a side by side comparison of the accuracy of the 427098 and the 43-215C using the same load of Swiss? It seems to me that the wide lube groove would effect the streamlining of the bullet when it spun off the lube. I am talking about 200 to 300 yards.  Jubal/Paul

Jubal, I have fired both bullets out to 300 meters (327 yards) and I will say that accuracy seems to be very close to the same. Paper targets @ 200 yards - showed almost the same group size for 10 shots - 427098 - 8 of the 10 shots inside 4", 43-215C - 8 of 10 shots inside 4". All 20 shots were inside 6".

58cal,
Welcome to the forum!  Thank you for the information.

David,
Thank you for the report. Nice shooting!  Excellent!   Much, much improved as compared to your first tests. ;D
Welcome to the world of making your own bullets!  ;D

The Accurate 43-220C is a very good choice for the 44-40 in combination with Swiss powder. It follows the same design as the 427098 (Accurate 43-210B - Fairshake) but with the crimp groove added which lengthens the bullet the width of the crimp groove (.04") and increases the weight.

I would agree that the alloy was not hot enough. I would suggest to try running the 30/1 alloy at 800F - 850F . You could preheat the mold in a toaster oven to bring it up to temp so that you will eliminate most of the rejects from a cold mold start up.  I use a toaster oven set at 450F to do that. Before placing the mold into the oven I remove the screws that are used to retain the handles. I turn on the pot and oven at the same time and let them warm up for a minimum of 1/2 - 3/4 hr.

Once up to temp, I use the mold handles to remove the mold from the oven then align the holes and insert the retaining screws.
I don't have the Lee 20# pot (I have the RCBS) but I looks like it has an adjustment to control the flow. Set it so that there is a fast drip then open it slightly so that it is a solid stream. As the alloy in the pot gets lower, adjustments will need to be made to keep the stream constant.  

I have had very good luck in making very good bullets with a bottom pour pot - on bullets up to 350 gr in weight. Over that and the dipper makes better bullets. As WM indicated, if you are still having a bit of trouble, you might want to try getting and using dipper.

If the mold is clean you should not need to smoke the cavities. If you do smoke the cavities, use wooden matches rather than a lighter.

I prefer to make mold contact with the spout which I find makes the base edges nice and sharp. I do have a few molds that seem to work better if I drop pour (mold below the spout by 1/2" or so.   I do find that spout contact has worked the best for me with the Accurate molds I have. 

Regarding Swiss 1 1/2 vs 2F, I have tried both and find them to be pretty equal accuracy wise. Since I like to = original factory ballistics (1,300 f.p.s.) I use mostly Swiss 2f.  Using standard large pistol primers 35 grs = 1,309 f.p.s..  It takes 38 grs of Swiss 1 1/2 to = 1,300 f.p.s. which requires more compression, but accuracy seems to be pretty much the same. Charges are by weight.

The same volume of 1 1/2 weighs just 1/2 gr less than the 2F in the lots that I have.

Happy new year!
w44wcf
  

    
  
« Last Edit: December 30, 2012, 11:12:22 am by w44wcf »
aka Jack Christian SASS 11993 "I can do all things through Christ who strengthens me." Philippians 4:13
aka John Kort
aka w30wcf (smokeless)
NRA Life Member
.22 W.C.F., .30 W.C.F., .44 W.C.F., .45 Colt Cartridge Historian

Offline David Battersby

  • Active citizen
  • *
  • Posts: 42
  • Smokeless powder is a passing fad .
Re: Black Powder in the 44-40
« Reply #66 on: December 30, 2012, 12:30:33 pm »

      I cast some 600 bullets yesterday afternoon and am now in the midst of pan lubing. I ran the pot at 800 degrees and preheated the mold more aggressively . Them is some purdy boolits !
 I will experiment with more 2f loads, up to at least 37 grains.
 I will post a picture of my Lee Turret Press with the modified Pro Auto Disc, the plastic hopper has been replaced with copper. It's not pretty but it works.

  The advice is very appreciated.

   David
John Moses Browning and Teddy Roosevelt, we need you again !
In the days of old when men were bold and a quarter was still worth a dime.

Offline wildman1

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 2723
Re: Black Powder in the 44-40
« Reply #67 on: December 30, 2012, 07:41:47 pm »
w44wcf is correct. I just weighed 30gs by measure of Swiss 1.5 and it weighed 33gs. WM
WARTHOG, Dirty Rat #600, BOLD #1056, CGCS,GCSAA, NMLRA, NRA, AF&AM, CBBRC.  If all that cowboy has ever seen is a stockdam, he ain't gonna believe ya when ya tell him about whales.

Offline w44wcf

  • Top Active Citizen
  • *
  • Posts: 1148
Re: Black Powder in the 44-40
« Reply #68 on: December 31, 2012, 09:29:47 am »
David,
Thank you for the update. Glad to hear that your latest casting session went better than the one previous.
"Them is some purdy bullets!"   Yes indeed! Better than store bought cast bullets. Quality can be much better too.

F.Y.I.
Chip Mate won the NRA Cowboy Silhouette Arizona State Champ with a score of 75x80 using a 44-40 Henry and 35 grs of Swiss 1 1/2 powder under a 200 gr RCBS bullet.  He does have to wipe after every 10 shots to maintain accuracy partially due to the less lube capacity of the RCBS bullet and partially because of the low humidity in the south.

Later he shot a perfect 40x40!
http://www.cascity.com/forumhall/index.php/topic,42343.0.html

Awesome shooting!
w44wcf 
aka Jack Christian SASS 11993 "I can do all things through Christ who strengthens me." Philippians 4:13
aka John Kort
aka w30wcf (smokeless)
NRA Life Member
.22 W.C.F., .30 W.C.F., .44 W.C.F., .45 Colt Cartridge Historian

Offline Space Cowboy

  • Active citizen
  • *
  • Posts: 35
Re: Black Powder in the 44-40
« Reply #69 on: January 28, 2013, 12:28:27 am »
Howdy,

Yesterday I shot my 44-40 Uberti 1873 to 100 m. I shot several 5 shot groups from a sandbag rest, the worst group was 5.7", the best was 3,3", but 4 shots from the best groups were in a 2.3" circle. I fired 25 shots with the rifle, and the best group was the 4th 5 shots. I did not clean the bore between shots, and did not use a blow tube.



Load: starline cases, 35gr 3Fg Swiss, Lyman 240 grain bullet sized to .427", primer: CCI 250 large pistol
Lube: mixed from 0W40 engine oil, beeswax and tallow

I am sure that this group can be improved with a better rest and diopeter sight.

I love this rifle.

cheers,
SC

Offline Space Cowboy

  • Active citizen
  • *
  • Posts: 35
Re: Black Powder in the 44-40
« Reply #70 on: January 28, 2013, 12:31:49 am »
One more thing. my rifle is sighted to 50 ms, so if I aim at the bottom of the black are the bullets fly into the ten ring. At 100 m the bullets hit the target just where I aim so trhe bullet drop between 100 and 50 m is cca 5".

Offline Rowdy Fulcher

  • NCOWS
  • Top Active Citizen
  • ***
  • Posts: 2724
Re: Black Powder in the 44-40
« Reply #71 on: January 28, 2013, 12:50:33 pm »
Space Cowboy
Thanks for sharing your shooting results . Have you had a chance to try them over a chronograph . The 35 grains of 3F Swiss is a hot load .

Offline w44wcf

  • Top Active Citizen
  • *
  • Posts: 1148
Re: Black Powder in the 44-40
« Reply #72 on: January 29, 2013, 10:23:05 am »
SC,
Thank you for the range report. ;D    I wonder if you sized the bullet to...say .429 or .430 (if it is large enough) if the average group size could be reduced.   I don't have a Uberti '73, but I have read that the groove diameters of those rifles are likely closer to .429" from those that have slugged their rifles.

w44wcf
aka Jack Christian SASS 11993 "I can do all things through Christ who strengthens me." Philippians 4:13
aka John Kort
aka w30wcf (smokeless)
NRA Life Member
.22 W.C.F., .30 W.C.F., .44 W.C.F., .45 Colt Cartridge Historian

Offline Rowdy Fulcher

  • NCOWS
  • Top Active Citizen
  • ***
  • Posts: 2724
Re: Black Powder in the 44-40
« Reply #73 on: January 29, 2013, 11:29:18 am »
Howdy
I switched to the .429 and it printed smaller groups . The .427 worked but the .429 was better .Uberti rifles have a larger bore .

Offline Space Cowboy

  • Active citizen
  • *
  • Posts: 35
Re: Black Powder in the 44-40
« Reply #74 on: January 29, 2013, 12:45:03 pm »
Yes, the bore is .428 so theoreticall 429 bullets work better. With this load I tried the 429 bullets, but they were hard to chamber in the rifle, and sometimes impossible to chamber in my revolvers. The bullet seemd to push out the brass.


 

Menu Editor Pro 1.0.2 | Copyright 2014, Matthew Kerle