Recent Posts

Pages: [1] 2 3 4 5 6 ... 10
1
The Darksider's Den / Re: Which rifle for BP?
« Last post by Sedalia Dave on Today at 05:56:15 PM »
Quote from: Griff on May 13, 2024, 04:52:51 PM
All y'all,,, and chemicals... although plastic bags can be right handy when it's rainin'! :D


 ;D ;D ;D ;D ;D
2
The Powder Room - CAS reloading / Re: Closest Substitute for Unique
« Last post by Sedalia Dave on Today at 05:39:33 PM »
Take a look at the data on this website.

http://www.gmdr.com/lever/lowveldata.htm

Pay close attention to the SD. Loads with high SD indicate erratic ignition.

YMMV
3
The Leather Shop / Re: New project holster/belt
« Last post by Crossdrawnj on Today at 04:05:42 PM »
Thanks to you both for your advise.  Would you use slightly heavier leather for the belt?
4
Gunsmithing / Re: Rossi 92 parts- will older interarms era parts fit newer guns?
« Last post by Froogal on Today at 06:19:26 AM »
Quote from: DeaconKC on Yesterday at 08:14:05 PM
Okay, here's the easy way to eliminate the safety. Drive the pin out that holds the safety in, remove the three parts. Take a .25 ACP case and cut it down to about an 1/8"-3/16" and Blue Lock-tite it in place. If you can find a W-W stamped case it looks even better.

And be aware there is a detent ball and spring in there. I saved the spring but the ball went to parts unknown.
5
Gunsmithing / Re: Rossi 92 parts- will older interarms era parts fit newer guns?
« Last post by Major 2 on Yesterday at 08:28:39 PM »
Seems to me, someone maybe Palo Verde Gunworks or UniqueTek makes a blanking screw to replace the Safety.
I know Palo Verde make one for the JM Marlins, I installed one on my 94CL along with their spring kit.

Edit:  Steves Guns  https://store.stevesgunz.com/index.php?main_page=product_info&products_id=95
6
Gunsmithing / Re: Rossi 92 parts- will older interarms era parts fit newer guns?
« Last post by DeaconKC on Yesterday at 08:14:05 PM »
Okay, here's the easy way to eliminate the safety. Drive the pin out that holds the safety in, remove the three parts. Take a .25 ACP case and cut it down to about an 1/8"-3/16" and Blue Lock-tite it in place. If you can find a W-W stamped case it looks even better.
7
The Leather Shop / Re: New project holster/belt
« Last post by Marshal Will Wingam on Yesterday at 06:48:16 PM »
I like 8-9 oz leather for unlined holsters. That's just slightly thicker than many of the ones from the later 1800s. A good wet molding and it will hold its shape well.
8
The Leather Shop / Re: New project holster/belt
« Last post by Macon Due on Yesterday at 06:40:45 PM »
Crossdrawnj
I am not an expert or a pro but I have made a few rigs and to me 10-12oz. seems a bit excessive. I am planning a California holster and Fair Weather Christian belt soon. It will be unlined and 7-9oz leather.
Macon
9
The Leather Shop / New project holster/belt
« Last post by Crossdrawnj on Yesterday at 05:20:59 PM »
I want to start a new holster/belt project. I have been making my rigs, both holster and belts lined: 7-8 ounce outer layer, 3-4 ounce inner layer. I want to do a rig unlined. I like a heavy combination. I am thinking of using 10-12 oz. or heavier for the belt and the holster.  I'd like to get a recommendation from the group here as there is a lot of experience on this site. Thanks in advance.
10
Bird Cage Theatre ( Videos ) / Re: Sixgun Spotlight - A New Series On My Channel
« Last post by Rube Burrows on Yesterday at 10:45:46 AM »
Quote from: Marshal Halloway on Yesterday at 09:44:05 AM
For the video to show up the URL link has to be with a .com like this
Code: [Select]
https://www.youtube.com/watch?v=b0AsnWmh9V8

Thanks. I will try to get that right.  ;)
Pages: [1] 2 3 4 5 6 ... 10
SMF spam blocked by CleanTalk
© 1995 - 2023 CAScity.com