Cimarron's Teddy Roosevelt Colt

Started by RRio, November 06, 2023, 04:52:23 PM

Previous topic - Next topic

RRio

I just got a Cimarron Teddy Roosevelt Colt over the weekend, and it is a beauty. While it is not a perfect replica of his Colt, it is a fine tribute to him and his Colt.
The action right out of the box is butter smooth and will not require me to do an action job. Since Uberti has gone the way of 3 click actions, Pietta has stayed with the tradition 4 clicks, and boy howdy, they have perfected them. The timing is dead on, bolt engaging the cylinder notch perfectly. Both hammer pull and trigger pull both on the light side but not too light. Weight and balance...   ...well, if you were to blindfold me, and place it in my hand, I'd be hard pressed to tell you if it was a Colt or not.  In short, I am very pleased with this Pietta built Cimarron.
"I hate rude behavior in a man. I won't tolerate it"  - Capt. Woodrow Call

"Proud citizen of CasCity since 2004." 
NCOWS 2492  SASS 22927   SCORRS     USFACS #28       GAF #267 Dept. of the Platte  AZ        STORM #178

Abilene

Looks good!  You've got the right props to go with it.  :)

Coffinmaker


:)  RRio  ;)

That there is a righteous fine looking TR replica.  REALLY nice.  I notice, in your photo it has the knurled assembly screw for the Base Pin.  Somewhere in the box, should be the correct flush fitting screw for the Base Pin.  Often stuck thru a small hole in the cardboard.  Although Pietta is more prone to fitted foam for box interiors.

45 Dragoon

Nice looking revolver! 
Just fyi, no +p ammo - even if you get an  acp cyl for it.

Mike
www.goonsgunworks.com
Follow me on Instagram @goonsgunworks

RRio

Quote from: Coffinmaker on November 07, 2023, 07:18:32 AM
:)  RRio  ;)

That there is a righteous fine looking TR replica.  REALLY nice.  I notice, in your photo it has the knurled assembly screw for the Base Pin.  Somewhere in the box, should be the correct flush fitting screw for the Base Pin.  Often stuck thru a small hole in the cardboard.  Although Pietta is more prone to fitted foam for box interiors.

Coffinmaker,
I sent an email to Cimarron and told them I was missing the flush mount screw, they sent a replacement that week.

Now if we could get Pietta to make the groove all around the base pins in all guns, we'd be defecating in tall fibrous vegetation.    ;D
"I hate rude behavior in a man. I won't tolerate it"  - Capt. Woodrow Call

"Proud citizen of CasCity since 2004." 
NCOWS 2492  SASS 22927   SCORRS     USFACS #28       GAF #267 Dept. of the Platte  AZ        STORM #178

Coffinmaker


:) RRio  ;)

AMEN!!  That two position Base Pin is annoying at the least.  Even after it has been shortened, the latch consistently drops into the first notch.  Total annoyance.  I've kept mine but am leaning more and more toward a pair of Uberti base pins without the two position stupidity.

RRio

Quote from: Coffinmaker on December 08, 2023, 06:18:50 PM
:) RRio  ;)

AMEN!!  That two position Base Pin is annoying at the least.  Even after it has been shortened, the latch consistently drops into the first notch.  Total annoyance.  I've kept mine but am leaning more and more toward a pair of Uberti base pins without the two position stupidity.
That maybe a good solution. Will the Uberti's fit the Piettas? That would be cheaper than buying a new mini lathe.
"I hate rude behavior in a man. I won't tolerate it"  - Capt. Woodrow Call

"Proud citizen of CasCity since 2004." 
NCOWS 2492  SASS 22927   SCORRS     USFACS #28       GAF #267 Dept. of the Platte  AZ        STORM #178

Major 2

I believe I've read they do...  The Diameter of the Uberti pin is .248
when planets align...do the deal !

Abilene

The first thing I did when I got a Pietta was slap a Uberti base pin in it!  It hasn't even been shortened, but is much easier to install than the Pietta pin.  This one was a spare I had, but if I had to buy one I'd buy the shorter Uberti pin that goes to the current 3-clicker guns.

I asked Mike Harvey once if there was any chance of Pietta changing to an Uberti-style base pin with the grooves all the way around, but Pietta says "No Way".  I'm guessing they would have to pass a bunch more tests over again.

© 1995 - 2024 CAScity.com