Author Topic: Trouble  (Read 5305 times)

Offline Abilene

  • CAS-L Ghost Rider
  • Top Active Citizen
  • *
  • Posts: 4672
    • Abilene's CAS Pages
  • SASS #: 27489
  • NCOWS #: 3958
  • Liked:
  • Likes Given: 1180
Re: Trouble
« Reply #40 on: May 01, 2021, 11:22:58 AM »
If the binding is while you try to close the lever to push the cartridge into the chamber, then try pushing up on the carrier from the bottom while closing the lever to see if that is smoother.  If so, the carrier is not staying all the way up, usually due to insufficient tension from the carrier spring.

Offline Coffinmaker

  • Top Active Citizen
  • *
  • Posts: 7605
  • Liked:
  • Likes Given: 125
Re: Trouble
« Reply #41 on: May 02, 2021, 08:49:15 AM »

 :)  Hummmmmmm   ;)

Normally, a '76 wouldn't be in my wheel house, but I did work on a few in the past, and a Toggle Link Rifle is a Toggle Link Rifle.

A bullet with an excessively wide nose will hang up on the Barrel Breach Face.  Anything even looking like a Semi-Wadcutter will hang up on the Barrel Breach Face.  It's a Tube Magazine feel rifle.  It will not play well without a firm crimp.  Bullets without a crimp groove are a waste of time.  They WILL turtle.

The "Double Feed" indicates your ammunition is too short.  The Nose of the round in the Carrier Block has to be long enough to hold the next round far enough in the Magazine for the Return Ramp to be able to push the next round back into the tube.

The tolerance between the "Knob" of the Carrier Block Arm and the Raceway in the Carrier Block is such, you will not be able to get much if any Epoxy to change the lift.  The lift can be changed slightly by CAREFULLY bending the Arm.

ALWAYS work on the cheapest part FIRST.

Offline King Medallion

  • Top Active Citizen
  • *
  • Posts: 1180
  • SASS #: 14753
  • Liked:
  • Likes Given: 165
Re: Trouble
« Reply #42 on: May 02, 2021, 10:21:25 AM »
Thank you for the tip. Sounds like I have a bunch of single shot bullets.
King Medallion

Advertising

  • Guest
Re: Trouble
« Reply #43 on: Today at 10:27:51 AM »

Offline Slamfire

  • Top Active Citizen
  • *
  • Posts: 988
  • Liked:
  • Likes Given: 61
Re: Trouble
« Reply #43 on: May 02, 2021, 01:13:43 PM »
 Sorry I missed your OAL for your rounds???


 coffee's ready ,, Hootmix.

Offline greyhawk

  • Top Active Citizen
  • *
  • Posts: 1070
  • Liked:
  • Likes Given: 49
Re: Trouble
« Reply #44 on: May 03, 2021, 06:17:39 PM »
Sorry I missed your OAL for your rounds???


 coffee's ready ,, Hootmix.

I'll agree with Coffin Maker ----double feed sez round too short  - forget the book specs and load to suit the rifle.
 
Using blackpowder?  yees? use enough powder compression to support the rounds from "turtling"

maybe forget the crimp groove and crimp into the top of the lube groove or just crimp wherever is best length for the gun

needs some crimp to turn the neck of the case in or else that will hang up on the chamber mouth .

My Uberti (45/75 rifle) has a quite noticeable chamfer on the chamber mouth

I cut some of my cases short and crimp into the top of the lube groove.

If I make em full chamber length and crimp over the ogive = use the powder column to support the boolit position - that works too

blackpowder makes life easy assembling rounds for lever guns.
 
I get your frustration!!!!!!!.


Offline ndnchf

  • Top Active Citizen
  • *
  • Posts: 1419
  • Liked:
  • Likes Given: 1
Re: Trouble
« Reply #45 on: May 16, 2021, 06:11:57 AM »
KM - Any updates on your problem? Enquiring minds want to.know  ;D
"We're all travelers in this world.  From the sweet grass to the packing house, birth till death, we travel between the eternities"  Prentiss Ritter, Broken Trail

Offline King Medallion

  • Top Active Citizen
  • *
  • Posts: 1180
  • SASS #: 14753
  • Liked:
  • Likes Given: 165
Re: Trouble
« Reply #46 on: May 16, 2021, 09:22:51 AM »
Nothing yet, been bizzy.
King Medallion

Offline King Medallion

  • Top Active Citizen
  • *
  • Posts: 1180
  • SASS #: 14753
  • Liked:
  • Likes Given: 165
Re: Trouble
« Reply #47 on: June 09, 2021, 01:26:05 PM »
Just ordered my first mold, an Accurate 51-350CL, 2 cavity.

The mold finally arrived today! Vacation next week to Kentucky, then I will dive into this casting thing. I bought an old Lyman model 61 bottom pour pot at a gun show awhile ago, and got a Lyman 45 Colt mold too. And a bunch of lead. So now its a matter of finding that last ingredient, time.
King Medallion

Offline pinto beans

  • Top Active Citizen
  • *
  • Posts: 219
  • Liked:
  • Likes Given: 40
Re: Trouble
« Reply #48 on: June 09, 2021, 03:14:13 PM »
Mr. King if you find a supply of that time ingredient let me know, I have run short of that most all my life and in retirement it is not to be found!! 

Seriously, good luck with it and keep us posted on the outcome.

P.B.

Offline King Medallion

  • Top Active Citizen
  • *
  • Posts: 1180
  • SASS #: 14753
  • Liked:
  • Likes Given: 165
Re: Trouble
« Reply #49 on: October 22, 2021, 04:39:43 PM »
So, loading up a few of the Barnes 450 JFN, AOL is 2.25. Feed and function perfectly, so far. I got some 330g bullets from Montana Bullet works I'm going to try also, with BP. I got a set of CH4D dies now so I'm fiddling with the settings. I will be using the RCBS bullet seat die to crimp alone.
King Medallion

 

SMF spam blocked by CleanTalk

© 1995 - 2023 CAScity.com