Author Topic: Steel Target Thickness  (Read 4254 times)

Offline Niederlander

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 3099
  • Liked:
  • Likes Given: 6
Steel Target Thickness
« on: February 18, 2010, 08:35:05 PM »
Hello!
     We intend to use mild steel to make some new targets.  We've always used half inch steel, but many people online say 3/8" is fine for lead bullets at our velocities.  Any opinions here?  Thanks!
"There go those Nebraskans, and all hell couldn't stop them!"

Offline River City John

  • NCOWS Senator
  • NCOWS Member
  • Top Active Citizen
  • ***
  • Posts: 4413
  • Mr. & Mrs. John Covert
  • NCOWS #: L-146
  • GAF #: 275
  • Liked:
  • Likes Given: 463
Re: Steel Target Thickness
« Reply #1 on: February 19, 2010, 05:45:46 PM »
I would stick with 1/2" if you're going to blast away at 'em with the military longarms.

RCJ ;)
"I was born by the river in a little tent, and just like the river I've been running ever since." - Sam Cooke
"He who will not look backward with reverence, will not look forward with hope." - Edmund Burke
". . .freedom is not everything or the only thing, perhaps we will put that discovery behind us and comprehend, before it's too late, that without freedom all else is nothing."- G. Warren Nutter
NCOWS #L146
GAF #275

Offline Drydock

  • MA1 USN ret. GAF #19, Colonel, Chief of Staff. BC, CC, SoM. SASS 1248 Life
  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 4831
  • Liked:
  • Likes Given: 18
Re: Steel Target Thickness
« Reply #2 on: February 19, 2010, 06:11:43 PM »
All my testing was done on 3/8" plate, with no adverse affects using lead bullets at no more than 1400 FPS.  I cannot say what the hardness was, but you should be OK.
Civilize them with a Krag . . .

Advertising

  • Guest
Re: Steel Target Thickness
« Reply #3 on: Today at 06:47:00 AM »

Offline Niederlander

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 3099
  • Liked:
  • Likes Given: 6
Re: Steel Target Thickness
« Reply #3 on: February 19, 2010, 06:45:57 PM »
I'm tending towards the 3/8", as we'll get more targets for the money.  We're getting close to a test run of the new half scale Blunt skirmish targets.  I'll keep everyone informed of our progress.
"There go those Nebraskans, and all hell couldn't stop them!"

Offline Pitspitr

  • Deputy Marshal
  • Top Active Citizen
  • *
  • Posts: 4592
  • 308 214-0082 45551 Rd 816, Sargent NE 68874 USA
    • Grand Army of the Frontier
  • SASS #: 74523
  • NCOWS #: L187
  • GAF #: 147
  • Liked:
  • Likes Given: 2
Re: Steel Target Thickness
« Reply #4 on: February 21, 2010, 10:58:33 AM »
Hi Ned
My big tombstone/quigley bucket target is 3/8" I've shot it for several years. I regularly shoot it with a full .45/70-535. It's mild steel and the only discernable damage to it is where a 535gr bullet was tumbling and impacted the target sideways. You can make out part of the bullet profile including the lub rings.  I've even shot it with FMJ .45 ACP from my Thompson with only a few minor dimples.

With the velocity and bullet weight restrictions we impose on GAF shooters I think you can have the targets cut from 3/8" and not need to worry much about target damage.

Another thing to consider is that if at somepoint down the road we do start seeing target damage, the club will probably have save enough money to replace the target,s so return on investment would also seem to favor 3/8''.
I remain, Your Ob'd Servant,
Jerry M. "Pitspitr" Davenport
(Bvt.)Brigadier General Commanding,
Grand Army of the Frontier
BC/IT, Expert, Sharpshooter, Marksman, CC, SoM
NRA CRSO, RVWA IIT2; SASS ROI, ROII;
NRA Benefactor Life; AZSA Life; NCOWS Life

Online pony express

  • Top Active Citizen
  • *
  • Posts: 3629
  • Liked:
  • Likes Given: 0
Re: Steel Target Thickness
« Reply #5 on: February 22, 2010, 07:08:53 PM »
Of course you may have to add some sandbags to weigh it down if Rattlesnake Jack is gonna shoot it with his cannoh.....errr.....Martini.....

Offline Niederlander

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 3099
  • Liked:
  • Likes Given: 6
Re: Steel Target Thickness
« Reply #6 on: February 22, 2010, 08:59:43 PM »
I intend to do the testing with a .50-70 Springfield.   That should give me a pretty good idea how they'll hold up!
"There go those Nebraskans, and all hell couldn't stop them!"

Offline Pitspitr

  • Deputy Marshal
  • Top Active Citizen
  • *
  • Posts: 4592
  • 308 214-0082 45551 Rd 816, Sargent NE 68874 USA
    • Grand Army of the Frontier
  • SASS #: 74523
  • NCOWS #: L187
  • GAF #: 147
  • Liked:
  • Likes Given: 2
Re: Steel Target Thickness
« Reply #7 on: February 23, 2010, 06:40:09 AM »
I've shot mine with a lot of the .50/70 that you've loaded for me with nary a dimple. My .45/70/500 and 535's have been harder on it than the 50/70. Heavier bullet, faster velocity.
I remain, Your Ob'd Servant,
Jerry M. "Pitspitr" Davenport
(Bvt.)Brigadier General Commanding,
Grand Army of the Frontier
BC/IT, Expert, Sharpshooter, Marksman, CC, SoM
NRA CRSO, RVWA IIT2; SASS ROI, ROII;
NRA Benefactor Life; AZSA Life; NCOWS Life

Offline Drydock

  • MA1 USN ret. GAF #19, Colonel, Chief of Staff. BC, CC, SoM. SASS 1248 Life
  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 4831
  • Liked:
  • Likes Given: 18
Re: Steel Target Thickness
« Reply #8 on: February 23, 2010, 07:30:14 AM »
Yeah, with bullet weight its sectional density that really kills targets.  IE for the same velocity, long and heavy is worse than wide and heavy.  More mass/force concentration at point of impact.  Thats why we limit the .45s to 405 grains, but let you use a 480 in the .50s
Civilize them with a Krag . . .

 

SMF spam blocked by CleanTalk

© 1995 - 2023 CAScity.com