Cas City Forum Hall & CAS-L
Special Interests - Groups & Societies => SCORRS => Topic started by: Tuolumne Lawman on October 10, 2021, 01:30:43 PM
-
Well, I have been using a Schofield and a either a Kirst 1860 Saber River Konversion or 1872 Open Top as my main match pair, but hvae been missing having a Remmie. I already have a Kirst Pale Rider and ejector rod, so I have an 1858 Pietta on back order (due in end of next week).
Probably going to eventually mill out a loading notch in the solid Pale Rider recoil plate, and make it gate-less like the originals. A 5 shot like the original .46 Rimfires is correct. Shooting Schofield would have been feasible back then with a modified hammer. .46 rimfire was basically a rimfire .45 Schfield. The .46 RF case was only .02" (two hundredths) of an inch larger, and the bullet was .456 instead of the .454 of the Schofields.
The Schofield and the Kirst will still be my main guns, but the Remmie will be my back-up main match pistol.
-
My Pale Rider NMA with my other Kirst pistols
(https://i.imgur.com/LOjoFFS.jpg)
-
Decided against modifying the Pale Rider recoil plate. Instead ordered the gated ring separately from Old South Firearms fo $200. Going to do the full on gated conversion. They are just plain cool.
-
Well, I cut the loading channel in the recoil shield of my Pietta NMA (1858). DANG! This had the hardest steel of any of the Piettas I have Kirst Konverted! Holy Cow, I went through 8 Dremel drums - 6 coarse and one fine, instead of the 4+1 I usually use. Covered the areas I wanted to protect with Gorilla tape, but still had two small buggered areas from the drum jumping more than normal. Oh well, I got it done. Now I need some faux-ivory grips.
I installed a Kirst ejector rod assembly, but left the rammer installed. Just as on some original NMA conversions I have seen with the rammer left on, as it would have allowed shifting back to a percussion cylinder in a pinch, where the .46 Rimfire ammo was not available in the far reaches of the frontier.
(https://i.imgur.com/nthmlxo.jpg)
-
Looks good! I'm surprised Walt doesn't offer an ejector that has a tab that's is caught by the rammer the way some originals were. Love the cartridge box, too.
-
I have searched high and low, and can not find a picture of what an original .46 rimfire box looks like. I did find the picture of the .46 short bullet from the box of Winchester (because of the H head stamp in the picture), so I use red paper like 1870s Winchester pistol cartridge boxes used on their labels, and formatted the rest like a Winchester cartridge box in another pistol caliber.
From "Cartridges of the World", I got the original factory loads for .46 rimfire. Remington loaded a 227 grain bullet over 20 grains of powder with a grease wad, and Winchester loaded a 230 grain bullet over 26 grains of powder.
-
Looks good! I'm surprised Walt doesn't offer an ejector that has a tab that's is caught by the rammer the way some originals were. Love the cartridge box, too.
The one that Uberti makes like that does not have a spring. I have handled them and think a spring-loaded ejector rod like the Kirst that doesn't need the rammer to be unlatched each time is a lot more handy.
-
I had an Uberti factory NMA conversion for a bit, and it was OK, but seemed like it was significantly bigger that the percussion. I know it is supposed to be 10% bigger to accommodate a 6 shot .45 Colt cylinder, but to me it seemed even bigger than that!
I have four percussion Pieta that I Kirst Konverted. I think I enjoy them more, because I am the one who really created them. My two 1860s (8" & 3") have replaced everything else as main match pistols. They are uber-cool, and totally in character with my 1869 Persona, who had private .46 rimfire long cylinder conversions to go with his 1860 Henry. The .46 caliber (with a .456" bullet) conversions were far more accurate than the LCC that used .44 Rimfire, as that .438/.440" diameter bullet would bounce down the .454/456" bore of the Colt 1860s and Remington NMA.
-
I always believed the barrels were sleeved on the 44 rimfire conversions? It would be cool if they werent lol. Get her done! ;D
-
From what research I did for my conversion articles, they were not lined, at least in most cases, hence poor accuracy from the .44s.
-
The one that Uberti makes like that does not have a spring. I have handled them and think a spring-loaded ejector rod like the Kirst that doesn't need the rammer to be unlatched each time is a lot more handy.
I was just thinking of what to do with that unattractive tab sticking down. Plus it makes properly fitting a holster difficult.
I have searched high and low, and can not find a picture of what an original .46 rimfire box looks like. I did find the picture of the .46 short bullet from the box of Winchester (because of the H head stamp in the picture), so I use red paper like 1870s Winchester pistol cartridge boxes used on their labels, and formatted the rest like a Winchester cartridge box in another pistol caliber.
From "Cartridges of the World", I got the original factory loads for .46 rimfire. Remington loaded a 227 grain bullet over 20 grains of powder with a grease wad, and Winchester loaded a 230 grain bullet over 26 grains of powder.
It does look good. With no original to copy, you made a believable label.
-
I was just thinking of what to do with that unattractive tab sticking down. Plus it makes properly fitting a holster difficult....
Oh yeah, definitely agree. But then TL don't care about no holster fit - he uses big ol' flap holsters! :)
-
LOL! Actually It fits in a Oklahoma Leather "Slim Jim" very nicely!
(https://i.imgur.com/qBYJjYs.jpg)
-
These may be useful:
-
Label info#2:
-
Oh yeah, definitely agree. But then TL don't care about no holster fit - he uses big ol' flap holsters! :)
LOL!
LOL! Actually It fits in a Oklahoma Leather "Slim Jim" very nicely!
(https://i.imgur.com/qBYJjYs.jpg)
You can't argue with success, then. ;D
-
:D Ho Kay!! Listen UP :o
Just received a missive from Maggie Enns at Howell Arms. They now have Gated Conversions in stock for '58 Remington.
I have no financial interest. I do not receive gratuities. I do not personally like Remington so have no Dog inna Fight. Public Service Announcement.
Play Safe Out There
-
That is good news. I wonder if they are 6 shot like when the came out? I don't mind the Kirst being a five shot, as most Remingtons were converted to 5 shot .46 Rimfire, which is nearly identical to the .45 Schofields I shot from it. My KIRST 1860s are 5 shot, too.
If I were to shoot a pair of 1858s, though, I'd probably go with the 6 shot Howells.
-
With four Open top Colts, I really don't need my Kirst Pietta Remington. I think Ill find it a new home... It would sell as a BP revolver with the Kirst stuff separate so no FFL. BTW, it's unfired.
(https://i.imgur.com/jDQX9K6.jpg)
-
I keep trying to love Remmies, but I stuck on open top Colts (I have four).
-
I don't even try to love Remingtons. Look cool but don't fit my hand. Same with S&W. I've never owned one of either. Only Colt style SAA and conversions. Same with modern revolvers. Some Colt snakes, but have never owned any other make. Not that others wouldn't fit me, but I quit buying modern guns once I started CAS. Well, no more modern than 1911, anyway. :)
-
I keep trying to love Remmies, but I stuck on open top Colts (I have four).
Nothing wrong with that. They either fit your hand or they don't. We're all different. Stay with what you like. :D
-
Yep, they don't fit my hands like the Colt Open tops. Same with the Smith and Wessons. Love the top break but don't shoot them worth squat! May put it in the classifieds. SASS wire classifieds can be a pain. Last time I sold a BP revolver with a Kirst there, all the know it alls jumped my @ss saying I could not sell them together, even though the wholesalers do....
-
Listed in the SASS wire classifieds for $595.
-
Hi
Schofields and Colt Army grips fit my hands. SAA not so much. Haven't tried a Remington Outlaw at this point. Got cowboy guns in .45 and two in .38, I hope to be done buying guns and just started buying ammunition.
Later
-
Hi
I hope to be done buying guns and just started buying ammunition.
HAHAHAHAHAHAHA!! That's funny! Stop buying guns, that's a hoot! :) ;) ;D