Author Topic: Need a Heavier Hammer spring for my New Vaquero  (Read 219 times)

Offline Doc Holloman

  • Citizen
  • *
  • Posts: 9
  • SASS #: 110783
  • Liked:
  • Likes Given: 0
Need a Heavier Hammer spring for my New Vaquero
« on: May 06, 2022, 11:55:04 AM »
You're thinking "You want a HEAVIER hammer spring?"   Yes, because my .357 New Vaquero is getting soft primer strikes one or two rounds out of every  five.  Not necessarily on the same cylinders.  This happens on both CCI and Winchester primers.  Yes, I know, I could use Federals, but these days I need to use what I can get and I have about 1000 rounds already loaded with Winchesters.

The Gun is clean, recently slicked up and has a Super Blackhawk hammer (so I don[t really want to send it back to Ruger and have them put a factory hammer back in.

Wolff does not make heavier than factory springs for the New Vaquero.  Does anyone?

TIA
JHE

Offline Abilene

  • CAS-L Ghost Rider
  • Top Active Citizen
  • *
  • Posts: 4036
    • Abilene's CAS Pages
  • SASS #: 27489
  • NCOWS #: 3958
  • Liked:
  • Likes Given: 611
Re: Need a Heavier Hammer spring for my New Vaquero
« Reply #1 on: May 06, 2022, 12:34:13 PM »
Hi Doc, I think on those coil spring guns that you can shim the main spring with a washer for more power.

Offline Baltimore Ed

  • Top Active Citizen
  • *
  • Posts: 1679
  • SASS #: 11754
  • Liked:
  • Likes Given: 103
Re: Need a Heavier Hammer spring for my New Vaquero
« Reply #2 on: May 06, 2022, 02:14:27 PM »
Somebody got a little too aggressive with their wire cutters maybe. Happens to everyone sooner or later.
"Give'em hell, Pike"
 There is no horse so dead that you cannot continue to beat it.

Offline 45 Dragoon

  • Top Active Citizen
  • *
  • Posts: 360
  • Liked:
  • Likes Given: 34
Re: Need a Heavier Hammer spring for my New Vaquero
« Reply #3 on: May 06, 2022, 04:11:19 PM »
 Yep. Cutting coils is a no no!! 
 Abilene's suggestion is a good one.

Mike
www.goonsgunworks.com
Follow me on Instagram @goonsgunworks

Offline Coffinmaker

  • Top Active Citizen
  • *
  • Posts: 6930
  • Liked:
  • Likes Given: 81
Re: Need a Heavier Hammer spring for my New Vaquero
« Reply #4 on: May 06, 2022, 04:26:41 PM »

 :) Doc  ;)

Two other things you may wish to verify.  Head Space.  Optimum head space for most any revolver is .004.  The other culprit is End Shake.  End Shake should be held to .001. Ruger is not known for tight tolerance.  If the end shake is contributing to open head space, your going to need to shim the cylinder bushing (that little thing stick out the front of the cylinder).

Then start shimming the Main Spring and checking the Firing Pin Extension.

Play Safe Out There

Advertisers

  • Guest
Re: Need a Heavier Hammer spring for my New Vaquero
« Reply #5 on: Today at 08:17:47 PM »

Offline Niederlander

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 2702
  • Liked:
  • Likes Given: 4
Re: Need a Heavier Hammer spring for my New Vaquero
« Reply #5 on: May 07, 2022, 07:55:28 AM »
Not totally on topic, but you might change to a Brownells round hammer strut.  I've got them in both my Ruger SA's, and I couldn't believe how much smoother they were than even a smoothed up factory strut.  I've never had any problem with light primer strikes, either.
"There go those Nebraskans, and all hell couldn't stop them!"

Offline Doc Holloman

  • Citizen
  • *
  • Posts: 9
  • SASS #: 110783
  • Liked:
  • Likes Given: 0
Re: Need a Heavier Hammer spring for my New Vaquero
« Reply #6 on: May 07, 2022, 10:42:19 AM »
Well, with the numerous possibilities that have been suggested, both here and on other sites, I’ve realized that I am probably in over my head. I admit I’m not much of a revolver guy (give me a 1911 or a Garand and I can deal with most issues.)   The trouble that the guy from my club (who IS a revolver guy) had reassembling my NV with the new hammer has made me leery of trying to do any more myself than replacing the spring.  So I will try shimming the old spring with washers (assuming I can find some that fit on the strut and under the grips) and if that doesn’t work, I need to send it off to someone who knows what he is doing.
Who do you recommend?  I see a lot of lists of Ruger pistol smiths online, but most of those are 5-10 years old, and I have already run across a few instances of gunsmiths who are getting out of the business or who are not taking new work.  As I think I mentioned, I don’t want o send it off to Ruger as they will probably put the factory spec high hammer back in.

Offline King Medallion

  • Top Active Citizen
  • *
  • Posts: 928
  • Liked:
  • Likes Given: 95
Re: Need a Heavier Hammer spring for my New Vaquero
« Reply #7 on: May 08, 2022, 08:04:17 AM »
If I read correctly, your spring has been cut too short? If thats so, why not simply buy a Wolf reduced weight spring? I have them on all my Blackhawks and have never ever had an issue. Just a thought.

Offline Doc Holloman

  • Citizen
  • *
  • Posts: 9
  • SASS #: 110783
  • Liked:
  • Likes Given: 0
Re: Need a Heavier Hammer spring for my New Vaquero
« Reply #8 on: May 08, 2022, 12:14:58 PM »
Spring does not look it was cut.  I shimmed it with a washer and have it reassembled.   Will have to wait until Tuesday afternoon before I can test fire it (local range is closed on Sunday and Monday. )  Will try with factory ammo.  I checked my ammo locker and I have Federal, CCI and Winchester .38 special ammo so I can try it with all 3 brands of primers.

If that doesn't work, then I may send it off to Cody at the Cowboy shop.

 

SMF spam blocked by CleanTalk

© 1995 - 2022 CAScity.com