Author Topic: Powder charge for Navy Colt with conicals  (Read 986 times)

Offline Niederlander

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 3099
  • Liked:
  • Likes Given: 6
Powder charge for Navy Colt with conicals
« on: October 04, 2021, 06:44:54 PM »
Gentlemen, I'm going to try authentic conicals in my Uberti Navy Colt.  How much powder fits under that an a felt wad?  Just need a starting point.  I know it's always 22 grains under a round ball.
"There go those Nebraskans, and all hell couldn't stop them!"

Offline DeaconKC

  • Retired Predator Hunter
  • Top Active Citizen
  • *
  • Posts: 1814
  • SASS #: 110215
  • Liked:
  • Likes Given: 4667
Re: Powder charge for Navy Colt with conicals
« Reply #1 on: October 04, 2021, 07:15:27 PM »
Check out this youtube channel, he does a lot of work with conicals and is fun to watch.
https://www.youtube.com/c/GunsOfTheWest
SASS DeaconKC
The Deacon AZSA
BOLD 1088
RATS 739
STORM 448
Driver for Howard, Fine & Howard
Veterinary & Taxidermy Clinic
"Either way, you get your dog back"

Offline Niederlander

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 3099
  • Liked:
  • Likes Given: 6
Re: Powder charge for Navy Colt with conicals
« Reply #2 on: October 05, 2021, 07:56:51 AM »
From what I've been able to find, it looks like about fifteen grains.  Should be a good place to start, anyway.
"There go those Nebraskans, and all hell couldn't stop them!"

Advertising

  • Guest
Re: Powder charge for Navy Colt with conicals
« Reply #3 on: Today at 10:15:49 AM »

Offline Coffinmaker

  • Top Active Citizen
  • *
  • Posts: 7605
  • Liked:
  • Likes Given: 125
Re: Powder charge for Navy Colt with conicals
« Reply #3 on: October 05, 2021, 09:06:53 AM »

 :)   Ah Ha  :D

A question I can answer !!!  Okay !!! I don't have a clue  :o   Never shot conicals although another shooting friend has sent me some, haven't shot 'em to date.  But, it's really simple.  Take the cylinder out of the gun (or not).  With a stick that fits the chamber, first measure the conical from base to tip.  Mark stick with pencil (or Pen).
Pour some poudre into the chamber until it reaches the bottom of the stick when the stick is held with the mark on the lip of the chamber.  Then add just a little more so you can compress it.

Now . . . . and this as really really important . . . . the actual amount of poudre is completely immaterial.  Seriously.  So long as you get a tad of compression, your gold.  Oh, I almost forgot.  I suggest 3F.

See !!  There it is.  Super simple.  Shouldn't take more-n-hour to figure out.  Easy Peasy.

People are Hazardous to Yer Health
Avoid Them

Offline Drydock

  • MA1 USN ret. GAF #19, Colonel, Chief of Staff. BC, CC, SoM. SASS 1248 Life
  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 4831
  • Liked:
  • Likes Given: 18
Re: Powder charge for Navy Colt with conicals
« Reply #4 on: October 07, 2021, 05:44:42 PM »
The military charge was 17 grains powder, no wad, bullets dip lubed in Paraffin wax.
Civilize them with a Krag . . .

Offline Pettifogger

  • Top Active Citizen
  • *
  • Posts: 3613
  • Liked:
  • Likes Given: 19
Re: Powder charge for Navy Colt with conicals
« Reply #5 on: October 07, 2021, 06:53:12 PM »
Not rocket science with BP.  Put in enough powder so the ball and wad will seat below the level of the front of the cylinder.  Weight is irrelevant.  Take a dowel and mark it so the mark is at the length of the ball and wad.  Keep putting powder into the chamber and inserting the dowel until it is filled to your mark on the dowel.

Offline Niederlander

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 3099
  • Liked:
  • Likes Given: 6
Re: Powder charge for Navy Colt with conicals
« Reply #6 on: October 07, 2021, 09:27:37 PM »
The military charge was 17 grains powder, no wad, bullets dip lubed in Paraffin wax.
I'm thinking fifteen with a wad would be a good place to start then.  I'll order a 15 grain spout for my flask and adjust from there.
"There go those Nebraskans, and all hell couldn't stop them!"

Offline Coffinmaker

  • Top Active Citizen
  • *
  • Posts: 7605
  • Liked:
  • Likes Given: 125
Re: Powder charge for Navy Colt with conicals
« Reply #7 on: October 08, 2021, 08:12:32 AM »

 :)  Niederlander   ;)

Tother day I completely forgot.  For my .36 Navy's, I really like the EPP UG-36 bullet.  It weighs in at a whopping 90Gr and has a rebated base to square it up on the chamber mouth.  The thing also has an enormous Lube Groove and carries a boat load of lube.  Finding the powder charge is exactly the same as my and Pettifogger's above methods.

People are Hazardous to yer Health
Avoid Them

 

SMF spam blocked by CleanTalk

© 1995 - 2023 CAScity.com