Special Interests - Groups & Societies > RATS

Necessity is the mother.

(1/3) > >>

Baltimore Ed:
Started on a primer oriented project last week. As I have twice as many small rifle/ pistol primers [9000] than I have large pistol primers I needed a way to use the small ones to stretch the large primers. Came up with 2 thoughts. I have 85 pcs of .455 MkII brass with small primer pockets, they drop into my Vaquero cylinders fine except for the occasional rim touching the center raised ratchet area. After numerous tries i have finally machined a .020 thick spacer to go between the thin case rims and cylinder but doesn’t bind anywhere and the hammer sets the srp’s off fine. I did turn down the raised ratchet a hair and replaced the too weak mainspring. Only made it a 5 shooter as it’s kinda delicate. Need to make a couple more. I’ve blued it now.
The other idea was to get a .45 acp cylinder fit to my Vaquero to use the small primer 45acp cases [have 500 plus]. Knew I was saving those aggravating small primer cases for something. This way I can use small primers in my SA and DA revolvers and 1911 [WB] and lg primers in my rifle ammo. Instead of using 120 lg primers/shoot I’ll use 60 small and 60 large. I just won the auction so the acp cylinder won’t be here until next week. Hopefully things will get back to some kind of normal before we all are using airsoft.

DeaconKC:
Well done Sir!

Baltimore Ed:
I’ve figured out the machining technique on the shims and made a nicer one yesterday. Need one or two more like that. Now I have them in my two main 4.5 inch vaqueros. I had lightened to hammer springs to speed up my duelist shooting but found that they wouldn’t set off the small rifle primers every time. Scrounged around in my spring box and luckily found one that was long enough to get two pcs 24 coils long. I used my drill press to install them. No way I could have done it by hand. They worked fine but felt too heavy so I clipped one coil off my Bowen tuned gun and one and a half off the stock gun. Both feel about the same and set off the harder primers fine. I did have to turn down the ratchet radius as it was interfering with the larger .455 rims on some of the chambers. Either differences in the brass or in the cylinder machining. My .45acp small primer brass came today so now I’ve got plenty for WB and will only need to use my large pistol primers in my cas rifle reloads.  Also found another box of .455 small primer fiocchi.

Baltimore Ed:
The .45acp cylinder to be here Monday. It’s in Raleigh. As the cylinders easily swap on my 3.5 in Birdshead and 7.5 in Vaqueros I’ll try to fit this one to them. Shot some .45 acp srp loads in the AO 1911, gun ran fine and rang and clanged my steel.

Baltimore Ed:
My 45acp cylinder finally arrived. Thought it was blued but now I think its matte stainless. Did Ruger offer a blasted finish .45acp single action? It fits except that the piece [collar?] the protrudes from the cylinder around the base pin is too short. With the gate open it spins fine but with the gate closed the cylinder is touching the bbl and partially binding. When I looked harder I saw where the collar? does not touch the frame. I did fire 5 rds of my small primer 45 acp loads through it ok. Any ideas on how to add a spacer to this? Some kind of endshake washer that I could epoxy on the cylinder?
I also built another nice shim for the .455 brass so both of my 4.5 in vaqueros will work with small primer .455 Webley.

Advertisers:

Navigation

[0] Message Index

[#] Next page

Go to full version
Powered by SMFPacks Ads Manager Mod
Powered by SMFPacks Likes Pro Mod
Powered by SMFPacks Menu Editor Mod