Cowboy & Western Action Shooting
Posts:
Recents
.
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email
?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
News & Blogs
Home
Posts
Recent Posts
Help
Business Directory
Calendar
Advertising Rates
Contact Us
Login
Register
Cas City Forum Hall & CAS-L
»
Special Interests - Groups & Societies
»
SCORRS
»
Question about Revolver Carbine!
0
Likes
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Question about Revolver Carbine! (Read 2755 times)
amin ledbetter
Top Active Citizen
Posts: 542
Tell 'em I'm comin! And Hell's comin with me!!!!!
Liked:
Likes Given: 0
Question about Revolver Carbine!
«
on:
February 05, 2010, 05:41:02 PM »
I have been reading Dusty Morningwood's post on his revolver Carbine project. He mentioned at the beginning of his post that his Carbine had an 18" barrel. Well that sparked my interest so I checked Uberti's website and seen sure enough, they listed the carbine as an 18" barrel as well. So I went and dug mine from the safe and measured mine again. My old Uberti revolver carbine has a 20" barrel. Measured from the barrel breech at the cylinder to the muzzle tip end. Does Uberti measure theirs from the end of the frame to the muzzle tip or from the breech to the muzzle tip?? Mine measure's 18 7/16th from the end of the frame to the muzzle tip. My Carbine is old! Proof mark dates it as manufactured in 1971. Were the barrels 20's" back then or do I have an oddball?
Logged
amin ledbetter
Top Active Citizen
Posts: 542
Tell 'em I'm comin! And Hell's comin with me!!!!!
Liked:
Likes Given: 0
Re: Question about Revolver Carbine!
«
Reply #1 on:
February 06, 2010, 09:42:15 AM »
Here's a pics of my carbine's barrel measurement.
Logged
Major 2
"Still running against the wind"
Deputy Marshal
Top Active Citizen
Posts: 15937
NCOWS #: 3032
GAF #: 785
Liked:
Likes Given: 428
Re: Question about Revolver Carbine!
«
Reply #2 on:
February 06, 2010, 09:52:08 AM »
Trained Attack cat ?
Logged
when planets align...do the deal !
Advertising
Guest
Re: Question about Revolver Carbine!
«
Reply #3 on:
Today
at 08:20:48 AM »
Logged
Wolfgang
Top Active Citizen
Posts: 1343
Liked:
Likes Given: 0
Re: Question about Revolver Carbine!
«
Reply #3 on:
February 06, 2010, 11:43:20 AM »
If'n ya miss 'em with the bullet . . . . ya can whack 'em with the barrel . . . or sick the cat on 'em . .
Logged
Beware the man with one gun, he probably knows how to use it.
Angel_Eyes
Top Active Citizen
Posts: 715
Liked:
Likes Given: 0
Re: Question about Revolver Carbine!
«
Reply #4 on:
February 06, 2010, 12:20:45 PM »
You lot are a 'barrel' of laughs!!
And that pistol goes against the grain, (sic.)
Hold on, ( 'paws' for thought), I don't make jokes as a 'rule'!
Sorry, I'll stop now,,,
AE
Logged
Trouble is...when I'm paid to do a job, I always carry it through. (Angel Eyes, The Good, The Bad & The Ugly)
BWSS # 54, RATS# 445, SCORRS,
Cowboy from Robin Hood's back yard!!
Dusty Morningwood
Top Active Citizen
Posts: 696
Liked:
Likes Given: 0
Re: Question about Revolver Carbine!
«
Reply #5 on:
February 06, 2010, 05:35:06 PM »
Quote from: amin ledbetter on February 06, 2010, 09:42:15 AM
Here's a pics of my carbine's barrel measurement.
My barrel is 18" from same point. Why did they change the length?
Logged
amin ledbetter
Top Active Citizen
Posts: 542
Tell 'em I'm comin! And Hell's comin with me!!!!!
Liked:
Likes Given: 0
Re: Question about Revolver Carbine!
«
Reply #6 on:
February 06, 2010, 07:18:16 PM »
Dusty,
I can't seem to find any info that the Carbines were any other length other than 18" Can't seem to figure out why mine is 20". It is a Uberti Barrel as their logo is stamped on the left side of the barrel.
Don't know when why or even if they did!!!! I wander if Uberti could ( would ) tell me any info about this?
Logged
Print
Pages: [
1
]
Go Up
« previous
next »
Cas City Forum Hall & CAS-L
»
Special Interests - Groups & Societies
»
SCORRS
»
Question about Revolver Carbine!
SMF spam
blocked by CleanTalk
© 1995 - 2023 CAScity.com