Author Topic: Aftermarket for Miroku 92?  (Read 983 times)

Offline Doc Holloman

  • Very Active Citizen
  • *
  • Posts: 69
  • SASS #: 110783
  • Liked:
  • Likes Given: 0
Aftermarket for Miroku 92?
« on: December 12, 2022, 02:18:57 PM »
I recently picked up a Winchester Miroku 92 in .38-40 with an octagon barrel.   Love the gun but would like to make a couple of "improvements.).  It has a semi buckhorn rear sight and a plain blade front.  Would like to replace them with a rear notch, and a white  bead front.    The only replacement sights I can find are for the Rossi or for an original Winchester.  Does anyone know if either will fit the Miroku?

Also, the magazine spring is rather stiff,  and requires a lot of effort to load the last couple of rounds.  Rather than cut the factory spring, I would like to get an aftermarket spring and experiment cutting it down gradually.  Again, will a spring for the Rossi or original winchester work in the Miroku?

Finally the rifle has a tang mounted safety.  It there anything difficult about disabling it?  I accidentally flipped it on a couple of times last time I shot it.

Thanks in advance.

Doc

Offline Buckaroo Lou

  • Top Active Citizen
  • *
  • Posts: 523
  • Liked:
  • Likes Given: 93
Re: Aftermarket for Miroku 92?
« Reply #1 on: December 12, 2022, 10:33:04 PM »
Marbles makes a beaded front sight. All the Miroku rifles I have seen come with a semi buckhorn rear sight and a gold beaded front sight.

I would think an original magazine tube spring would work but not absolutely certain.

http://www.marblearms.com/front-sights.html

I don't know about disabling the tang safety.



A man's true measure is found not in what he says but in what he does.

Offline Abilene

  • CAS-L Ghost Rider
  • Top Active Citizen
  • *
  • Posts: 4672
    • Abilene's CAS Pages
  • SASS #: 27489
  • NCOWS #: 3958
  • Liked:
  • Likes Given: 1180
Re: Aftermarket for Miroku 92?
« Reply #2 on: December 12, 2022, 10:52:41 PM »
Somebody in this topic mentions that his Mirokus have a .393" dovetail, although that is 1873 models:
https://www.cascity.com/forumhall/index.php?topic=58090.0

And this discussion on Miroku '92's says 3/8" :
https://castboolits.gunloads.com/archive/index.php/t-350165.html


Advertising

  • Guest
Re: Aftermarket for Miroku 92?
« Reply #3 on: Today at 07:37:46 AM »

Offline Doc Holloman

  • Very Active Citizen
  • *
  • Posts: 69
  • SASS #: 110783
  • Liked:
  • Likes Given: 0
Re: Aftermarket for Miroku 92?
« Reply #3 on: December 12, 2022, 11:32:20 PM »
And I wonder if the dovetail is different for an Octagon barrel.

Mine has the semi buckhorn, which I don't like.  Want to swap it for a flat top v-notch.  That is what I have on my  Uberti '73 in .38-40.   It oes have a gold bead on the front sight but it is so tiny I cant see it.  My 73 has a larger white one, which again is what I would prefer.

Offline Buckaroo Lou

  • Top Active Citizen
  • *
  • Posts: 523
  • Liked:
  • Likes Given: 93
Re: Aftermarket for Miroku 92?
« Reply #4 on: December 13, 2022, 10:00:59 AM »
There is a chart on the Marbles link I provided that shows the bead comes in two different sizes and in either gold or ivory and various heights and widths. They also have several different rear sights one being flat with v notch.
A man's true measure is found not in what he says but in what he does.

Offline Abilene

  • CAS-L Ghost Rider
  • Top Active Citizen
  • *
  • Posts: 4672
    • Abilene's CAS Pages
  • SASS #: 27489
  • NCOWS #: 3958
  • Liked:
  • Likes Given: 1180
Re: Aftermarket for Miroku 92?
« Reply #5 on: December 13, 2022, 10:36:47 AM »
New sights are not very expensive, but many also just file down the ears on the semi-buckhorn to make it a flat top.

Offline Black River Smith

  • Top Active Citizen
  • *
  • Posts: 1179
  • Liked:
  • Likes Given: 36
Re: Aftermarket for Miroku 92?
« Reply #6 on: December 13, 2022, 11:27:56 AM »
Try this website/page.  Midwest Gunworks is a good place to do business with.  I have bought several different sights from them when changing out a Rossi 92's Octagon barrel sights.

 https://www.midwestgunworks.com/sights.html

Hope this helps.
Black River Smith

Offline cpt dan blodgett

  • Top Active Citizen
  • *
  • Posts: 1693
  • SASS Conv 2013
  • Liked:
  • Likes Given: 3
Re: Aftermarket for Miroku 92?
« Reply #7 on: April 02, 2023, 02:30:30 PM »
And I wonder if the dovetail is different for an Octagon barrel.

Mine has the semi buckhorn, which I don't like.  Want to swap it for a flat top v-notch.  That is what I have on my  Uberti '73 in .38-40.   It oes have a gold bead on the front sight but it is so tiny I cant see it.  My 73 has a larger white one, which again is what I would prefer.

Really cannot see them using a different cutter and stocking a totally different sight but who knows.
I have a miroku 92 carbine but my only 24 inch octo is a rossi so no help
Queen of Battle - "Follow Me"
NRA Life
DAV Life
ROI, ROII

 

SMF spam blocked by CleanTalk

© 1995 - 2023 CAScity.com