Recent Posts

Pages: [1] 2 3 4 5 6 ... 10
1
RATS / Re: Ruger Old Model Super Blackhawk Ejector Screw
« Last post by Niederlander on Today at 02:30:05 PM »
I've sent a message to Ruger but haven't heard back yet.
2
Gunsmithing / Re: 1873 rifle headspace measurement
« Last post by Ghostdevilguy on Today at 01:41:23 PM »
Thanks for the info Coffenmaker!

I will give Pioneer gunworks a call and probably get an new short stroke kit with lifter. After observing the action it also appears that the lifter starts to later than it should. It starts moving after the bolt is done moving, and from what I'm seeing it should just miss the bolt
3
Frontier Iron / Re: Cimarron's new American model!
« Last post by U.S.M.R. on Today at 01:18:34 PM »
Smith and Wesson wrote UMC asking why Russian ammunition cost more than American ammunition. UMC replied that Russian ammunition used Berdan primers which they had to pay a royalty on and that they were loaded with pistol powder. That implies the American cartridges were loaded with something else. The 60 grs difference in bullet weight was not mentioned.
4
Tip from a fellow Carbine shooter; work the lever more briskly to and fro. Faster in one fluid motion without stopping. Down and back, down and back. Mine is a .44 S&W Russian version and she likes it rough. The faster the better.  Leave the butt on your shoulder, look down the sights and run that lever as fast as you can, then thumb the hammer back before tripping the hammer.  ;D
5
RATS / Ruger Old Model Super Blackhawk Ejector Screw
« Last post by Niederlander on Today at 12:06:22 PM »
Gentlemen, Where do I find the Old Model Ejector Rod Housing Screw for the Super Blackhawk?  It's the quarter inch one for the revolvers with a barrel stud.  Been looking online and can't find any.
6
The Longbranch / Re: How is Cimarron customer service?
« Last post by Gundogblue on Today at 11:11:11 AM »
As I said I’ve read a couple bad things, but that doesn’t mean they’re true. Dissatisfied customers gripes travel much faster than satisfied customer compliments! But it seems no one on this forum has had any dealings with Cimarron customer service, so evidently they must have quality products.
Paul
7
The Longbranch / Re: How is Cimarron customer service?
« Last post by Gundogblue on Today at 11:04:14 AM »
Uh oh, do that mean what I think it do??? :o
8
NCOWS / Re: Small pistol primers
« Last post by Coffinmaker on Today at 10:29:47 AM »

 :) Ah Ha  :P

I came up with a brilliant solution to the Small Pistol Primer shortage a couple Lustrum ago.  .45s.  Yep.  There it is.  I use nothing but Large primers for everything, including Shotgun.  Keeping it Simple Simon I are.
9
The Longbranch / Re: How is Cimarron customer service?
« Last post by Coffinmaker on Today at 10:20:46 AM »

 :) Noooooo Comment  :-\
10

 :) Harrumpff  ;)

Gotta define "slow."  I personally don't define 30 seconds as being "slow."  Unless your timing Usane Bolt, or waiting for Coffee Water to Boil.

I will qualify however, I haven't personally experienced any "slow."  CASCity has been working just fine.  I don't, however, consider surfing the Web onna "Phone" to be real practical inna first place.  At least not without a Sherlock.
Pages: [1] 2 3 4 5 6 ... 10
SMF spam blocked by CleanTalk
© 1995 - 2023 CAScity.com