Author Topic: USFA Plinker date of manufacture?  (Read 1931 times)

Offline Ken50

  • Citizen
  • *
  • Posts: 4
  • Liked:
  • Likes Given: 0
USFA Plinker date of manufacture?
« on: November 13, 2019, 11:36:50 AM »
Hi All,
I was wondering if anyone can help identify the approximate manufacture date of my USFA Plinker. It has a 4.75" barrel, case colored frame, rubber grips, serial number 22687. I am also interested to know if its parts were made in the USA if possible.

Best regards,
Ken

Offline Dave T

  • NCOWS Member
  • Top Active Citizen
  • ***
  • Posts: 1058
  • Liked:
  • Likes Given: 901
Re: USFA Plinker date of manufacture?
« Reply #1 on: November 14, 2019, 09:16:09 AM »
Never heard of a "Plinker" model, but there's a lot of things I've never heard of. That serial number range (22,000) would put it in the "probably some Uberti parts" catagory.

Dave

Offline Buckaroo Lou

  • Top Active Citizen
  • *
  • Posts: 523
  • Liked:
  • Likes Given: 93
Re: USFA Plinker date of manufacture?
« Reply #2 on: November 14, 2019, 06:01:40 PM »
Might could tell with photos of the cylinder flutes, firing pin, front sight, cam section on the ejector housing, good close clear profile of the revolver.
A man's true measure is found not in what he says but in what he does.

Advertising

  • Guest
Re: USFA Plinker date of manufacture?
« Reply #3 on: Today at 02:45:46 AM »

Offline Ken50

  • Citizen
  • *
  • Posts: 4
  • Liked:
  • Likes Given: 0
Re: USFA Plinker date of manufacture?
« Reply #3 on: November 14, 2019, 06:43:38 PM »
Hi,
The Plinker is a .22 revolver. It has a .22LR and a .22Mag cylinder. Photos attached.
Thanks!
Ken

Offline Buckaroo Lou

  • Top Active Citizen
  • *
  • Posts: 523
  • Liked:
  • Likes Given: 93
Re: USFA Plinker date of manufacture?
« Reply #4 on: November 15, 2019, 05:18:14 PM »
From the photos you have provided it appears there are at least some USA parts, coned firing pin and short rounded cylinder flutes. You didn't provide a good photo of the ejector housing cam area to see if it is the short fast cam or the longer gradual USA cam design. Is the front sight tapered, thinner at the top than at the bottom or is it the same thickness from base to top. Is the rear sight groove on the top of the frame pinched (v shape) or a squared notch. Yahoody posted a series of photos on another post as a method of determining if a specific revolver is composed of USA or Italian parts. I am not sure since it is a .22/.22 mag if all the USA part identifying characteristics still apply. Perhaps Yahoody would know.

http://pistolsmith.blogspot.com/2015/05/uberti-or-usfa-or-parts-gun.html


Blue Book of Gun Values states the USFA Plinker was made between 2004-2012. Yahoody also has a list of serial numbers and dates the revolvers on his list were made. It is on another post on this forum.
A man's true measure is found not in what he says but in what he does.

Offline Ken50

  • Citizen
  • *
  • Posts: 4
  • Liked:
  • Likes Given: 0
Re: USFA Plinker date of manufacture?
« Reply #5 on: November 20, 2019, 09:29:30 PM »
Thanks for the great information Lou!
In answer to your questions, the ejector housing has a long gradual cam, the front sight is the same thickness top to bottom, and the rear sight groove is a square notch.

Thanks!
Ken

Offline Buckaroo Lou

  • Top Active Citizen
  • *
  • Posts: 523
  • Liked:
  • Likes Given: 93
Re: USFA Plinker date of manufacture?
« Reply #6 on: November 23, 2019, 06:18:09 PM »
From your photos you have provided and what you have said sounds to me you may have an all USA revolver. I am sure Gary Granger would know and also were it falls in the range of serial numbers Yahoody has would indicate as well.
A man's true measure is found not in what he says but in what he does.

Offline Ken50

  • Citizen
  • *
  • Posts: 4
  • Liked:
  • Likes Given: 0
Re: USFA Plinker date of manufacture?
« Reply #7 on: November 24, 2019, 09:36:48 PM »
Thank you Lou, I appreciate your help!
Ken

Offline LonesomePigeon

  • Top Active Citizen
  • *
  • Posts: 592
  • Liked:
  • Likes Given: 5
Re: USFA Plinker date of manufacture?
« Reply #8 on: May 27, 2020, 03:02:50 PM »
I know this is an old post but it has a good picture of  the hammer on a .22 caliber gun. I was wondering how it is that a .22 rimfire gun could have a firing pin that looks like a center fire?

Offline Buckaroo Lou

  • Top Active Citizen
  • *
  • Posts: 523
  • Liked:
  • Likes Given: 93
Re: USFA Plinker date of manufacture?
« Reply #9 on: May 27, 2020, 06:45:58 PM »
It strikes on the rim of the cartridge and not in the center.
A man's true measure is found not in what he says but in what he does.

 

SMF spam blocked by CleanTalk

© 1995 - 2023 CAScity.com