Author Topic: Disassembly Instructions for an 1858 Pietta Remington Revolver  (Read 38212 times)

Offline Bull Schmitt

  • Top Active Citizen
  • *
  • Posts: 945
  • Liked:
  • Likes Given: 0
Disassembly Instructions for an 1858 Pietta Remington Revolver

http://www.scorrs.org/articles/1858disassembly.htm

Other Remington Revolver Gunsmithing information:

http://www.scorrs.org/gunsmith.htm
Bvt Col Bull Schmitt
GAF Adjutant General
GAF Commander Department of the Atlantic
GAF Webmaster
SCORRS President & Webmaster
SASS #9535, SCORRS, GAF, NRA

Offline GunClick Rick

  • Top Active Citizen
  • *
  • Posts: 10068
  • Scudders all of yas~
  • Liked:
  • Likes Given: 1
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #1 on: May 15, 2009, 12:25:15 AM »
Well i got it all apart ready to put it back together,any instuctions for that?? :'( ;) ;D
Bunch a ole scudders!

Offline Skinny Preacher 66418

  • Top Active Citizen
  • *
  • Posts: 224
  • Liked:
  • Likes Given: 0
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #2 on: May 15, 2009, 09:04:08 AM »
Well i got it all apart ready to put it back together,any instuctions for that?? :'( ;) ;D

Reassembly is impossible. You'll have to scrap it. I'll give you $25 for it if you'll mail it to Texas.  :D
Smoke em if ya got em.

Advertising

  • Guest

Offline Wolfgang

  • Top Active Citizen
  • *
  • Posts: 1343
    • The Desperate Hot Springs News
  • Liked:
  • Likes Given: 0
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #3 on: June 12, 2009, 09:55:53 AM »
Reassembly is impossible. You'll have to scrap it. I'll give you $25 for it if you'll mail it to Texas.  :D

Rick . . I'll make ya a better offer.   You pay me $ 20 to take it and send it to me in Desperate Hot Springs.  . . . . that way yu'll save money as the postage is less than to Texas which is a furrin cuntry . . .  ;D . . . sound like a good deal ? . .  :)
Beware the man with one gun, he probably knows how to use it.

Offline GunClick Rick

  • Top Active Citizen
  • *
  • Posts: 10068
  • Scudders all of yas~
  • Liked:
  • Likes Given: 1
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #4 on: June 14, 2009, 01:52:15 PM »
Money order on the way :D Rats,i forgot to put a stamp on it and they sent it back...Now i need a stock for that 12 incher..
Bunch a ole scudders!

Offline Daniel Nighteyes

  • Top Active Citizen
  • *
  • Posts: 1061
  • Liked:
  • Likes Given: 0
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #5 on: July 15, 2009, 12:55:51 PM »
Those instructions work great ---- for a revolver with the full-length barrel.  I have a pair of stainless Piettas with 5.5-inch barrels, and the cylinder pins come to a full stop on the loading lever latch before they can be removed.

Any suggestions on how I can remove the cylinder pins without completely dismounting the lever latches?  The pins are a little rough, and I'd like to smooth them out to facilitate removing/replacing the cylinders.

Offline Montana Slim

  • NCOWS Member
  • Top Active Citizen
  • ***
  • Posts: 1940
  • Liked:
  • Likes Given: 101
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #6 on: July 23, 2009, 08:58:00 PM »
Daniel, Probably cannot remove the pins via "simple" means. If the retaning stud has a dovetail, you can knock it out and then remove the cylinder pin, otherwise the retaining stud is soldered in (like my DIY "bob" job).

I cut my full barrel to ~4" some years ago. I don't fret over removing the pin for cleaning. You should be able to round/polish the tip of the cylinder pin. This should greatly smooth/improve installation of the cylinder. Polishing the entire length is not necessary unless it is extremely rough.

Regards,
Slim
Western Reenacting                 Dark Lord of Soot
Live Action Shooting                 Pistoleer Extrordinaire
Firearms Consultant                  Gun Cleaning Specialist
NCOWS Life Member                 NRA Life Member

Offline Angel_Eyes

  • Top Active Citizen
  • *
  • Posts: 715
  • Liked:
  • Likes Given: 0
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #7 on: July 24, 2009, 06:25:14 AM »
No problem Daniel,,,just cut off the piece of barrel with the lever catch attached,,,simple!!

AE

Sorry,,,couldn't resist it! :-[
Trouble is...when I'm paid to do a job, I always carry it through. (Angel Eyes, The Good, The Bad & The Ugly)
BWSS # 54, RATS# 445, SCORRS,
Cowboy from Robin Hood's back yard!!

Offline Daniel Nighteyes

  • Top Active Citizen
  • *
  • Posts: 1061
  • Liked:
  • Likes Given: 0
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #8 on: July 24, 2009, 06:54:48 PM »
No problem Daniel,,,just cut off the piece of barrel with the lever catch attached,,,simple!!

AE

Sorry,,,couldn't resist it! :-

I kin always count on you, Angel Eyes...    ::) ;D ;D ;)

Offline Flint

  • Top Active Citizen
  • *
  • Posts: 1096
  • Liked:
  • Likes Given: 0
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #9 on: July 24, 2009, 09:21:15 PM »
My 5-1/2 inch Uberti the lever catch (barrel stud) is just held in tight enough in the dovetail to stay in place, latched.  With the lever down, the barrel studs can be pushed out of the barrel with my fingers.  Sometimes the stud might prefer to move one direction more than the other, try pushing both directions to test it.  If you can't press it out sideways with your fingers, use a brass or wood dowel and a small mallet.  If they get too loose after some use and time, the dovetail can be tightened a bit with a few dimples punched at the edge of the barrel flat.

To disassemble, lower and remove the loading lever and press out the barrel stud, and the cylinder pin can be pulled out.
The man who beats his sword into a plowshare shall farm for the man who did not.

SASS 976, NRA Life
Los Vaqueros and Tombstone Ghost Riders, Tucson/Tombstone, AZ.
Alumnus of Hole in the Wall Gang, Piru, CA, Panorama Sportsman's Club, Sylmar, CA, Ojai Desperados, Ojai, CA, SWPL, Los Angeles, CA

Offline Professor Marvel

  • purveyor of useless items to the gentry
  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 3081
  • learn from the past, or be doomed to repeat it
  • Liked:
  • Likes Given: 1118
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #10 on: March 05, 2010, 12:27:08 AM »
Ah My Dear Daniel-san
I am beside myself, here you are at odds with your Remmy pins, and I fail to notice your dilemma for well over 9 months.

So the answer to your problem is the hinged cylinder pin, as perfected by other members of this excellent place.

The most difficult part for cutting any Remmy shorter than 5.5" is the cylinder rod. Since the loading lever catch blocks the free movement of the cylinder pin, anything shorter that that means the pin is permanently captured unless the latch is removed. Anything shorter than 4- 4.5" means the pin will not be able to clear the cylinder. Amongst the solutions I have seen are leaving off the loading lever and catch (ideal for a barrel 3" or less) , building a hinged cylinder pin, or planning for a removable lever catch (not a good choice IMHO).

I offer a small selection of links showing the efforts of others in this endevour -

First go here and drool:
http://www.alliancelink.com/srrs/photos.htm

Read about the "Ultimate Remington":
http://www.alliancelink.com/srrs/articles/ultrem.htm

You can  Learn How to chop it yourself:
http://www.chipengelmann.com/Grips/Remmies.html
http://www.hobbygunsmith.com/Archives/Jun03/HowTo.htm
http://www.hobbygunsmith.com/Archives/Feb04/Feature.htm

here you can see how Halfway Creek Charlie (aka Gunslinger in CAS) cut an 8" bbl, .44 Remington 6shot conversion, with his special hinged cylinder pin that allows a barrel shorter than 5 1/2 "

www.thefiringline.com/forums/showthread.php?t=300356

hope this helps
yhs
prof marvel
Your Humble Servant
~~~~~Professor Algernon Horatio Ubiquitous Marvel The First~~~~~~
President, CEO, Chairman,  and Chief Bottle Washer of


Professor Marvel's
Traveling Apothecary
and
Fortune Telling Emporium


Acclaimed By The Crowned Heads of Europe
Purveyor of Patent Remedies, Snake Oil, Powder, Percussion Caps, Cleaning Supplies, Dry Goods,
and
Picture Postcards

Offering Unwanted Advice for All Occasions
and
Providing Useless Items to the Gentry
Since 1822
[
Available by Appointment for Lectures on Any Topic


Offline blainenay

  • Citizen
  • *
  • Posts: 1
    • Ol' Buffalo Shooting Page
  • Liked:
  • Likes Given: 0
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #11 on: July 10, 2010, 10:56:11 PM »
Disassembly Instructions for an 1858 Pietta Remington Revolver

http://www.scorrs.org/articles/1858disassembly.htm

Other Remington Revolver Gunsmithing information:

http://www.scorrs.org/gunsmith.htm

I followed the steps as described. When I got the gun back together, there was no spring tension on the hand to engage and rotate the cylinder. I took the gun apart again to inspect the hand and spring. They appear to be normal. Any idea why I’m not getting spring tension on the hand?
A cold gun barrel is bad for the soul.

Offline Bishop Creek

  • Top Active Citizen
  • *
  • Posts: 168
  • Black Powder Shootist
  • Liked:
  • Likes Given: 0
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #12 on: March 03, 2011, 11:13:05 PM »
Hey, the directions worked!



Offline Wolfgang

  • Top Active Citizen
  • *
  • Posts: 1343
    • The Desperate Hot Springs News
  • Liked:
  • Likes Given: 0
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #13 on: September 13, 2011, 06:22:49 AM »
Comes appart prett good . . . does it go back to gether again ?    ;)
Beware the man with one gun, he probably knows how to use it.

Offline Octagonal Barrel

  • Top Active Citizen
  • *
  • Posts: 118
  • Liked:
  • Likes Given: 0
Re: Disassembly Instructions for an 1858 Pietta Remington Revolver
« Reply #14 on: September 23, 2013, 08:04:40 PM »
Comes appart prett good . . . does it go back to gether again ?    ;)
First time I took mine apart, I didn't need instructions.  It was enough like Colts that I figured it out on my own.

Back together again?  I did have to spend several hours on the internet looking for creative suggestions on re-installing the main spring...  (By the way, the mainspring that came stock with my ASP Remmie was much stronger than most Remmie mainsprings, which made it much worse.  I've since replaced it with a lighter Pietta mainspring, and I don't need to be nearly as creative as that first time.)
Drew Early, SASS #98534

 

SMF spam blocked by CleanTalk

© 1995 - 2023 CAScity.com