Recent Posts

Pages: 1 [2] 3 4 5 6 7 ... 10
11
Tall Tales / Re: December coffee and grub
« Last post by Silver Creek Slim on Yesterday at 10:37:49 AM »
Morning y'all.
Coffee and tea are hot.

'Tis 11 and sunny. WC -2. High of 22.

Slim
12
Spencer Shooting Society / Re: spencer brass and mold for original
« Last post by matt45 on Yesterday at 09:21:24 AM »
I'm only constrained by the room in my gun safe and my wife  ;)
13
The Winchester Model 1876 / Re: Loading Data for the 45-60 WCF
« Last post by King Medallion on Yesterday at 08:57:03 AM »
This is what my brass looks like after fresh resize and belling with the new RCBS dies. Crimps nice, but very tight in there, never felt that in any seat die before.
14
1860 Henry / Re: Miroku 1866 - action won't close
« Last post by major on Yesterday at 07:32:13 AM »
I made one mistake in my post.  The gun I was having trouble with was a 73 not a 66, but the action is similar enough to have it apply to either.  IIRC The problem only seamed to manifest itself when there was a cartridge in the chamber.  It has been a few years so I am not sure I remember everything about it.
15
16
1860 Henry / Re: Miroku 1866 - action won't close
« Last post by Abilene on December 02, 2022, 11:01:36 PM »
I had a similar problem with a Muriko 1966 Winchester in 44-40. 
The problem with my gun was there was just a little to much meat on the block that is attached to the bold.  And when it mated up with the frame that extra material would make it difficult to close the bolt.  I took a small amount off the block on the bolt and it now works fine.  I only took a very little off the bolt block and not the frame because if I screwed it up the bolt is a lot cheaper to replace then the frame.  If you want more details send me a PM and maybe we can work it out over email.  Here are some picture.
Did it have that interference when unloaded or only when cycling cartridges?  The original poster said it only happened with cartridges.  However, he only made two posts and hasn't been back for nearly two months, so who knows?
17
The Leather Shop / Re: Sunday Holster
« Last post by 1961MJS on December 02, 2022, 10:19:33 PM »
Hi
I searched and found it here:
https://leathercraftersjournal.com/product/lone-star-holster-pattern-pack/
I didn't see it on Will's sight though.  I need to go back over the list and see if I have something that needs a Brill Holster.
Later
18
1860 Henry / Re: Miroku 1866 - action won't close
« Last post by major on December 02, 2022, 08:53:57 PM »
I had a similar problem with a Muriko 1966 Winchester in 44-40. 
The problem with my gun was there was just a little to much meat on the block that is attached to the bold.  And when it mated up with the frame that extra material would make it difficult to close the bolt.  I took a small amount off the block on the bolt and it now works fine.  I only took a very little off the bolt block and not the frame because if I screwed it up the bolt is a lot cheaper to replace then the frame.  If you want more details send me a PM and maybe we can work it out over email.  Here are some picture.
19
The Leather Shop / Re: Sunday Holster
« Last post by Rube Burrows on December 02, 2022, 08:26:52 PM »
Will's El Dorado holster isn't a Brill design. I didn't see a Brill on his site. You could email him to see if he has the pattern available.

He does have them available. It's called the Lone Star Holster pattern pack.
20
USFA CSS / Re: Gary Need your Help !
« Last post by GaryG on December 02, 2022, 03:31:03 PM »
Hartford Box made the boxes for USFA.  They were almost around the corner from USFA.  They closed up about 10 years ago.  It was a 3 person operation - 2 sisters and one of the husbands.   I think there was someone on this site that had some boxes made up to USFA specs but my mind is failing right now.
Pages: 1 [2] 3 4 5 6 7 ... 10
SMF spam blocked by CleanTalk

© 1995 - 2022 CAScity.com