Recent Posts

Pages: 1 [2] 3 4 5 6 7 ... 10
Tall Tales / Re: February,29 Mondays of Cawfee,Tea and vittles
« Last post by DeaconKC on Yesterday at 07:28:03 PM »
Well, been a bit busy here the last few days. Pretty weather, if I could get the back to quit growling, I would enjoy it more. I carried a 642 for many years as my pocket gun. Got talked out of it by a Williamson County Detective some years ago. Today my always gun is a Ruger LCP2 in .380 with the 7 round magazine, what a great little gun. Got my Sunday School lesson ready for tomorrow. May God bless you all, my friends.
STORM / Wedge question
« Last post by DeaconKC on Yesterday at 07:15:41 PM »
Okay, question about an 1851 .38 Special conversion. Ran tight at the range, hanging up with cartridges in the cylinder. Tried the trick of adding the split washer, but then the wedge was almost impossible to drive in. Can I file the wedge down to ease the fit without compromising safety. It seems that would be preferable to trying to file either the barrel assembly.
Spencer Shooting Society / Re: Shooting A Spencer Carbine In 45 Colt
« Last post by Abilene on Yesterday at 07:15:08 PM »
The wood finish on that carbine is different from what I'm used to seeing on the Chiappa Spencers, though I haven't seen a new one in quite some time.  It is also very pretty wood!
Cas City - Forum Support & Comments / Re: CASCity = Slow as molasses.
« Last post by Abilene on Yesterday at 07:08:17 PM »
It's always been slow to open the page at first for me, but after it's open, works just fine.
Now that you mention it, when I am not at home and therefore the phone is not on wifi, sometimes the same happens to me, takes longer to open that 1st page than some other sites, but then is fine.
Tall Tales / Re: February,29 Mondays of Cawfee,Tea and vittles
« Last post by Major 2 on Yesterday at 07:07:54 PM »
I have to say, I like this spare Rounds pouch.

It is heavy duty, came with 4 speed load strips (holds 2 = 10 rounds)
It will be on my left side belt and the J Frame in a Desantis pocket holster in my right pocket.
I wore it to a Restaurant tonight for its first outing.

I give it two thumbs up   ;D
The Longbranch / Re: How is Cimarron customer service?
« Last post by Mogorilla on Yesterday at 06:02:32 PM »
I have nothing but good things to say.  Bought a Cimarron 1878 colt shotgun.  But iI did not buy from them, saved $25 and got it from cheaper than dirt.  After a box of shells right hammer spring broke. I sheepishly called Cimarron and they sent me a new one.   I call that good service. 
I have received 7 registrations so far.

Looking forward to an amazing event!
RATS / Re: Ruger Old Model Super Blackhawk Ejector Screw
« Last post by Niederlander on Yesterday at 02:30:05 PM »
I've sent a message to Ruger but haven't heard back yet.
Gunsmithing / Re: 1873 rifle headspace measurement
« Last post by Ghostdevilguy on Yesterday at 01:41:23 PM »
Thanks for the info Coffenmaker!

I will give Pioneer gunworks a call and probably get an new short stroke kit with lifter. After observing the action it also appears that the lifter starts to later than it should. It starts moving after the bolt is done moving, and from what I'm seeing it should just miss the bolt
Pages: 1 [2] 3 4 5 6 7 ... 10
SMF spam blocked by CleanTalk
© 1995 - 2023