Author Topic: 1871 Springfield Rolling Block trigger pull  (Read 4334 times)

Offline hatman

  • Top Active Citizen
  • *
  • Posts: 242
  • Liked:
  • Likes Given: 4
1871 Springfield Rolling Block trigger pull
« on: September 10, 2017, 12:38:27 AM »
I recently purchased an 1871 Springfield (Remington) rolling block rifle.
I'm really happy with how it looks, and shoots except for what seems like about a 30 pound trigger pull.
That's just a guess; could be 20-25, but it's pretty strong.

Do any of you guys have any wisdom about how to reduce the trigger pull on this rifle?


Offline Kent Shootwell

  • Top Active Citizen
  • *
  • Posts: 779
  • Got whiskey, will stumble.
  • Liked:
  • Likes Given: 22
Re: 1871 Springfield Rolling Block trigger pull
« Reply #1 on: September 10, 2017, 02:49:58 PM »
 I'm guessing you have a military rifle, I had a Burnside carbine you could carry by the trigger! Assuming your rifle is clean and properly oiled a  heavy trigger pull is governed by spring strength and sear angles. The correct sear notch on the hammer will allow the sear to move with out undue effort even with a heavy spring. The amount of engagement affects the amount of creep you feel befor the hammer falls. A well polished surface of both sear and hammer reduces the drag. This long winded (for me) explanation is to guide you towards a gunsmith to do the work needed. It's too easy for the untrained hand to get the angles wrong and at best ruin some parts but more likely to make a unsafe gun.
Little powder much lead shoots far kills dead.
Member, whiskey livers
AKA Phil Coffins, AKA Oliver Sudden

Offline hatman

  • Top Active Citizen
  • *
  • Posts: 242
  • Liked:
  • Likes Given: 4
Re: 1871 Springfield Rolling Block trigger pull
« Reply #2 on: September 11, 2017, 01:27:48 AM »
Thank you, Kent.
Not necessarily what I wanted to hear, but what I needed to hear.

Advertising

  • Guest
Re: 1871 Springfield Rolling Block trigger pull
« Reply #3 on: Today at 09:38:43 AM »

Offline hatman

  • Top Active Citizen
  • *
  • Posts: 242
  • Liked:
  • Likes Given: 4
Re: 1871 Springfield Rolling Block trigger pull
« Reply #3 on: September 23, 2017, 10:01:50 PM »
Upon further reflection (and more shooting)...
I've decided to leave the trigger pull as-is.
I like the idea of shooting it as it was built to be shot.
It's just a privilege to have a chance to shoot a piece of history.

Offline Lord Eoin MacKenzie

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 187
  • Liked:
  • Likes Given: 0
Re: 1871 Springfield Rolling Block trigger pull
« Reply #4 on: November 25, 2017, 04:39:55 PM »
I think that Lee Shaver, gunsmith is a Rolling block Guru.   He runs the Single Shot Exchange magazine.

Offline Dave T

  • NCOWS Member
  • Top Active Citizen
  • ***
  • Posts: 1058
  • Liked:
  • Likes Given: 901
Re: 1871 Springfield Rolling Block trigger pull
« Reply #5 on: November 26, 2017, 02:31:06 PM »
I had a NY State Militia 50/70 Rolling Block at one time. In an article I wrote concerning it and another militia rifle I had back then I described the RB's trigger thusly: imagine sliding a heavy brick across the top of a rough work bench with one finger until if finally fell of the end. That's what the trigger pull of that RB felt like.

Sounds like hatman may have found my old gun. (smile)

Dave

Offline LongWalker

  • Top Active Citizen
  • *
  • Posts: 370
  • GAF #: 911
  • Liked:
  • Likes Given: 12
Re: 1871 Springfield Rolling Block trigger pull
« Reply #6 on: November 26, 2017, 04:20:52 PM »
I once replaced the trigger spring in a NY Militia RB with one made of piano wire bent to the same profile.  Trigger pull was reduced about 12-13# (to 5# and some odd-ounces) but the creep was more noticeable.  After shimming the full-cock notch, it wasn't half bad. 

Then I traded it off for some forgettable rifle I "had to have", and have been kicking myself for 25 years. 
In my book a pioneer is a man who turned all the grass upside down, strung bob-wire over the dust that was left, poisoned the water, cut down the trees, killed the Indian who owned the land and called it progress.  Charles M. Russell

Offline Professor Marvel

  • purveyor of useless items to the gentry
  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 3081
  • learn from the past, or be doomed to repeat it
  • Liked:
  • Likes Given: 1118
Re: 1871 Springfield Rolling Block trigger pull
« Reply #7 on: November 26, 2017, 04:22:53 PM »
My Good Hatman -
here is a link to some informative videos on the RB from the Midway gunsmiths

https://videos.midwayusa.com/index.php/show/gunsmithing_-_how_to_reduce_the_trigger_pull_on_a_remington_rolling_block_pistol?id=1_vyo00isl


hope this helps
yhs
prof marvel
Your Humble Servant
~~~~~Professor Algernon Horatio Ubiquitous Marvel The First~~~~~~
President, CEO, Chairman,  and Chief Bottle Washer of


Professor Marvel's
Traveling Apothecary
and
Fortune Telling Emporium


Acclaimed By The Crowned Heads of Europe
Purveyor of Patent Remedies, Snake Oil, Powder, Percussion Caps, Cleaning Supplies, Dry Goods,
and
Picture Postcards

Offering Unwanted Advice for All Occasions
and
Providing Useless Items to the Gentry
Since 1822
[
Available by Appointment for Lectures on Any Topic


Offline Lucky R. K.

  • Purveyor of Fire & Brimstone
  • Top Active Citizen
  • *
  • Posts: 420
  • Liked:
  • Likes Given: 1
Re: 1871 Springfield Rolling Block trigger pull
« Reply #8 on: November 26, 2017, 08:23:36 PM »

If you install a weaker trigger spring and grind the hammer spring you can get down to a 3 or 4 lb. Trigger pull. Be careful when grinding the hammer spring. Do a little and test it.

I have a good 3_4lb trigger on my R rolling Block.
Greene County Regulators       Life NRA             SCORRS
High Country Cowboys            SASS #79366
Gunpowder Creek Regulators   Dirty RATS #568

The Wind is Your Friend

 

SMF spam blocked by CleanTalk

© 1995 - 2023 CAScity.com