stainless pins media

[rbertalotto]

Put the tumbler drum in the sink and fill with water and let it overflow for a few minutes until the water runs relatively clear.

Put an old towel in the sink and pour the whole mess into the towel. Let it drain through the towel. Pick out the brass and dump
the SS pins baxck into the drum for storage.

Easy Peasy!

[Dalion]

BTW, Buffalo Arms has one pound bags for $7.50.  That is where I got mine.

[Fairshake]

Dalion. That is a good price but if you add in shipping it will be very expensive for just one pound of media.
The Pellets LLc price of $6 a pound for 5 pound bags which is $30 and $10 shipping via Priority Mail is still the best deal that I have found.
Unless Buffalo Arms has changed the way they ship, I would like to see the shipping quote.
I like Buffalo Arms and they are the cheapest price to buy a lot of things from. I have purchased guns, Model B Thumblers and supplies from them for years.
I did however just need a card of Lee Shaver front sight inserts for my 1874 Sharps and ordered just them figuring they would put them into a regular mailing padded brown envelope and send it via the USPS.
I was wrong and they came via a UPS truck and when I saw my bill I almost fell over. The card of inserts was about $15 and the shipping was the same for a total of $28.
I will say that after my rather upsetting call they saw fit to reduce the charge to around $6 or so which is still high for a piece of metal that would have required nothing but a .48 cent stamp.
I still believe in them and will continue to buy but only when I have enough items to equal the shipping charges.

[Dalion]

I can't disagree with you on shipping issue.  I did order the media with a bunch of other stuff in a larger order.

[Long Gulch]

Howdy All, I have been interested in stainless steel media for a while and this thread has pushed me over the edge.
I ordered the whole set up from Buffalo Arms plus there was a couple of other things I had been wanting as well. I used the info from the Stainless Steel Media folks' website as far as the procedure of cleaning goes, i.e. - 5 lbs pins, 1 gal., water, 2tbsp dawn, 1/4 tsp Lemi-Shine, 2lbs of brass and away we go. Whiz-bang! All is bright and shiney like new again!

However, the Insturctions from Buffalo Arms for the Stainless Steel Media says to place THREE pounds of SS media in the tumbler barrel and fill with cold water until it covers the media by an inch. Put a table spoon of compound in with the water. (referring to the liquid cleaner that is apprently their own brand). Use 2-3 tablespooons if the cases are extremely dirty. You may then add up to EIGHT pounds of brass for polishing and cleaning.

Now, am I gonna turn around and order  the compound + shipping from our good friends up in the Gem State? Well no.
I don't begrudge anyone from making a good product, but I just ain't ready to place another order right away.

So here's the question. ( Oh, you knew there was going to be a question, right?  )

Has any one used an alternative method or product with SS media to clean more than TWO pounds of brass at a time?  
BTW I am using Thumbler's  Tumbler which holds 15 lbs.

Thanks Much,
LG

 

[Fairshake]

Long Gulch, I posted on this forum about purchasing the so called secret cleaning liquid that all vendors want you to buy in a package deal before.
I have been doing this since 1968 and have tried them all and they are over priced for what they do.
Try using Dawn/OXY or Palmolive/Oxy and you will find that the end results are even better. It takes only a squirt or two for the model B which I have used since 1970.
I also have a Thumblers UV 18, Frankford Arsenal, and shoe box vibratory machines that no longer see any use because they will not clean BP cases like the ceramic or SS pins with water and soap.
Be careful with the Lemi Shine as I added a little too much to a load of nickel 44WCF cases that are now copper colored.
I use just enough water to cover the contents of my model B by about a 1/2 inch or so. I have read where some are saying to use a gallon of water and that will not work any better. It also causes a load on the tumbler while cutting down on space that could be used for cases.
My method is to put in my cases first then cover with media. Then add the water and soap and Lemi Shine if you choose to do so. But only enough water to cover and no more. Later David

[Long Gulch]

Fairshake, I sure do appreciate the feedback. I am only using  1/4 teaspoon of  Lemi-Shine and it seems to be working well.
I did clean some 2 lbs of nickled 357 cases and they came out fine. The first bunch of cases I did were 44WCF using the SSmedia/dawn/Lemi-Shine/1 gal. H2O method and everything worked great there.

At present I am running about 6 lbs of 44 Russian with my own "Secret Recipe" that I will report on if it is successful.

BTW thanks for your fine work with the 44WCF cartridge I have been following the posts here on that fine old round and it has become my latest new favorite bullet to cast and load. All in GUNPOWDER of course!

LG

[Deadeye Dick]

Just got stainless steel pins from STM in Utah. Followed their instructions about cleaning the stainless steel pins by themselves first. Then ran about 250 .40 S&W cases through it. I was impressed. Absolutely clean inside and out. All of my black powder cases were already clean so I haven't given them a try yet. Will try them next. I used a shot of Dawn and about an eighth teaspoon of lemi-shine with about a half quart of water in a Thumler's AR 12 Tumbler. Just covered the brass and pins with water and tumbled for about 4 hours.  Haven't tried bottle-necked cases yet. If it does as well with them I won't go back to my ceramic media.
Deadeye Dick