Author Topic: colt 2nd generation cap and ball pistols  (Read 65172 times)

Offline kurt250

  • Top Active Citizen
  • *
  • Posts: 214
  • Liked:
  • Likes Given: 0
colt 2nd generation cap and ball pistols
« on: April 26, 2011, 09:29:27 PM »
where can you find parts? i need a wedge for a 1851 navy, and a few other parts. kurt250

Offline Pettifogger

  • Top Active Citizen
  • *
  • Posts: 3613
  • Liked:
  • Likes Given: 19
Re: colt 2nd generation cap and ball pistols
« Reply #1 on: April 26, 2011, 09:58:45 PM »
VTI.  Look at Uberti parts.  That's what Colt 2nd Gens used.

Offline Doc Sunrise

  • Top Active Citizen
  • *
  • Posts: 719
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #2 on: July 10, 2011, 09:07:03 PM »
The Colt Blackpowder Series guns did not just use Uberti parts.  There are major differences.  In fact many of the small parts were made here.  A Uberti wedge will need to be fitted to work.   You can try http://www.coltparts.com/.

Colt assembled and finished the "C" Series guns after they received "parts kits" from Val Forgett that were received from Uberti.  Thoses particular parts had to be within a much tighter specification range than the components used for Uberti's guns.  Colt had an actual Inspection Department that all of these "Parts Kits" had to go through.  This made for a much higher standard for parts specifications and higher quality parts being used to assemble the "C" Series.  A Navy Arms employee stated that parts that were rejected were reworked by Navy Arms until they were in spec.  You could easily exchange parts for Colts with very minor fitting.  On the other hand, a Uberti assembled gun would require a box of parts and a skilled crafstman some time to put together a completed working gun.

When Imperato took over and expanded the line up of models for the "F" Series, Uberti still supplied barrels, cylinders, and backstraps to Imperato.  Imperato's Iver Johnson Arms Company here in New Jersey produced the remaining parts used, and then took care of making sure that all parts were within Colt's specs before assembly.  Colt still performed some Color Case Hardening and finishing of parts, and also the final inspections on completed guns.

Colt's Blackpowder Series and Uberti guns are two different things.  

Advertising

  • Guest
Re: colt 2nd generation cap and ball pistols
« Reply #3 on: Today at 06:47:28 AM »

Offline Fingers McGee

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 1397
  • Smoke & Fire
  • SASS #: R28654
  • NCOWS #: 3638
  • Liked:
  • Likes Given: 6
Re: colt 2nd generation cap and ball pistols
« Reply #3 on: July 12, 2011, 11:51:38 AM »
While all Uberti replacement parts may not work, or require extensive fitting to work on a 2nd Gen Colt BP revolver; my experience with small parts (screws, hand/spring assy, trigger/bolt spring, and loading lever) is that they are pretty much drop in (the hand required some filing to get the timing right).  A new Uberti wedge from VTI or Taylors' will probably fall into the same category - and be cheaper than Coltparts.
Fingers (Show Me MO smoke) McGee;
SASS Regulator 28654 - L - TG; NCOWS 3638
AKA Man of many Colts; Diabolical Ken's alter ego; stage writer extraordinaire; Frontiersman/Pistoleer; Rangemaster
Founding Member - Central Ozarks Western Shooters
Member - Southern Missouri Rangers;
NRA Patron Life: GOA; CCRKBA; SAF; SV-114 (CWO4 ret); STORM 327

"Cynic:  A blackguard whose faulty vision sees thing as they are, not as they should be"  Ambrose Bierce

Offline Doc Sunrise

  • Top Active Citizen
  • *
  • Posts: 719
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #4 on: July 12, 2011, 03:29:48 PM »
I didn't mean to be harsh.  A recent thread made me boil a bit when someone said Colt's Blackpowder Series guns are just dolled up Ubertis.  >:(

Offline Fingers McGee

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 1397
  • Smoke & Fire
  • SASS #: R28654
  • NCOWS #: 3638
  • Liked:
  • Likes Given: 6
Re: colt 2nd generation cap and ball pistols
« Reply #5 on: July 12, 2011, 06:55:15 PM »
I didn't mean to be harsh.  A recent thread made me boil a bit when someone said Colt's Blackpowder Series guns are just dolled up Ubertis.  >:(

I know what you mean Doc.  I get a little agitated - ok down right incensed at times - at the same people for the same reason. 

Fingers (Show Me MO smoke) McGee

Fingers (Show Me MO smoke) McGee;
SASS Regulator 28654 - L - TG; NCOWS 3638
AKA Man of many Colts; Diabolical Ken's alter ego; stage writer extraordinaire; Frontiersman/Pistoleer; Rangemaster
Founding Member - Central Ozarks Western Shooters
Member - Southern Missouri Rangers;
NRA Patron Life: GOA; CCRKBA; SAF; SV-114 (CWO4 ret); STORM 327

"Cynic:  A blackguard whose faulty vision sees thing as they are, not as they should be"  Ambrose Bierce

Offline kurt250

  • Top Active Citizen
  • *
  • Posts: 214
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #6 on: July 14, 2011, 04:30:42 PM »
i know what you guys mean. there so many people who  think there dolled up italian guns. do any of you know if theres a place were you could buy blank nipples. i would like to machine them for a better cap fit on my colts. i don't mean completely blank, i want the threads but the nipple left un machined. kurt250

Offline Fingers McGee

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 1397
  • Smoke & Fire
  • SASS #: R28654
  • NCOWS #: 3638
  • Liked:
  • Likes Given: 6
Re: colt 2nd generation cap and ball pistols
« Reply #7 on: July 14, 2011, 10:56:16 PM »
i know what you guys mean. there so many people who  think there dolled up italian guns. do any of you know if theres a place were you could buy blank nipples. i would like to machine them for a better cap fit on my colts. i don't mean completely blank, i want the threads but the nipple left un machined. kurt250

I run Tresos and #10 Remingtons on mine.  RWS 1075s work too.

FM
Fingers (Show Me MO smoke) McGee;
SASS Regulator 28654 - L - TG; NCOWS 3638
AKA Man of many Colts; Diabolical Ken's alter ego; stage writer extraordinaire; Frontiersman/Pistoleer; Rangemaster
Founding Member - Central Ozarks Western Shooters
Member - Southern Missouri Rangers;
NRA Patron Life: GOA; CCRKBA; SAF; SV-114 (CWO4 ret); STORM 327

"Cynic:  A blackguard whose faulty vision sees thing as they are, not as they should be"  Ambrose Bierce

Offline Gatofeo

  • Citizen
  • *
  • Posts: 22
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #8 on: July 22, 2011, 10:09:36 PM »
I have a Colt 2nd generation 1851 Navy and I don't blame you for getting agitated.
I've long wondered why so-called "experts" sneer at what they call "spaghetti Colts" but buy Winchesters and Brownings made in Japan, by Hiroku. They've bristled when I called them Sushi Winchesters or Brownings, to make a point.
I have always considered my Navy to be a real Colt. And if I owned an 1886 Winchester made by Hiroku, I'd still consider it a Winchester.
And no, when I cock my 1851 Colt, it does not say, "Oh ... Solo ... Me ... O"   ::)
"A vast desert. Smoke. Brimstone. Pierced parchment. The ugly cat is much amused." -- The Quantrains of Gatodamus (1503-1566)

Offline St. George

  • Deputy Marshal
  • Top Active Citizen
  • *
  • Posts: 4827
  • NCOWS , GAF, B.O.L.D., Order of St. George, SOCOM,
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #9 on: July 23, 2011, 11:17:21 AM »
Re: 'Real' Black Powder Colts...
« Reply #2 on: April 09, 2010, 07:46:58 am »     

--------------------------------------------------------------------------------

Since you'd asked...

Throughout the storied history of Colt's, there has been a succession of illustrious models, from the innovative Paterson revolvers of the late 1830s to the 1860 Army--the principal sidearm of Civil War Union officers--to the 1873 Peacemaker and Model 1911A1, the most distinguished military sidearm in American history.

One of the more interesting footnotes in the company's story, however, began in 1971, when it made the unprecedented decision to re-introduce a model it had last built in 1873. With the reintroduction of the legendary 1851 Navy--a gun made famous by James Butler "Wild Bill" Hickok--Colt's embarked on an 11-year odyssey that would result in one of the most popular and collectible series the Hartford, Connecticut, armsmaker would ever produce.

The tale of the 2nd Generation Colt black-powder line actually began in the late 1950s with Val Forgett, founder of Navy Arms, and Italian gunmakers Vittorio Gregorelli and Aldo Uberti. They chose the Colt 1851 Navy as the first percussion revolver to be reproduced in Italy in 1958.

After a dozen years and thousands of Colt reproductions, the success of the Italian-made '51 Navy--which Aldo Uberti frequently supplied to filmmaker Sergio Lione and Clint Eastwood for early spaghetti westerns--had finally come to the attention of the company that invented it.

There have been countless tales how Colt's dusted off the old tooling from the 1851 and began manufacturing new guns at Hartford, which would have been very interesting had the tooling not been destroyed when a fire razed most of the factory on Feb. 4, 1864.

As for the tooling used to make the later percussion models produced through 1873, it was simply discarded over the years, so Colt's could never have brought back the 1851 Navy, or any other percussion era model had it not been for Forgett, Uberti and, ultimately, Lou Imperato.

Imperato, who founded Colt Blackpowder Arms Co. in 1993 (which produced the 3rd Generation Colt Blackpowder line through 2002), recalls that Forgett sold Colt's the components (rough castings) to build the first 2nd Generation 1851 Navy revolvers, which were completed at the Hartford factory from 1971 through 1973. The first C Series 1851 Navy repros included the now collectible Grant and Lee Navy sets.

However, late in 1973 Colt's decided to seek a new supplier of components and the following year Lou Imperato, its largest American distributor, took over.

The company's enthusiasm for the percussion revolvers was obvious in its decision to place the new Third Model Dragoon on the cover of its 1974 sales catalog.

The Dragoon and Navy models were listed along with the Python, Detective Special, Cobra, Agent, Diamondback, Trooper MKIII, Official Police MKIII, Lawman MKIII, 1873 Peacemaker Single Action Army models, and semi-autos. Unfortunately, labor disputes delayed the Dragoon in 1974, causing Colt's to take the unprecedented step of re-announcing the Dragoon model in 1975, when deliveries actually began.

The relationship with Imperato continued until Colt's discontinued the first series of percussion revolvers in 1976. This, however, was not the end of the black-powder line.

In 1973 Lou Imperato had purchased the Iver Johnson Arms Company in Fitchburg, Massachusetts. A year after Colt's discontinued the black-powder line, Imperato moved the Iver Johnson works to Middlesex, New Jersey, and approached Colt's with the idea of producing an entire line of black-powder pistols, which the Italians had been doing successfully since the late 1950s.

He came in with both barrels blazing, so to speak, reprimanding Colt's management. "[They're] your guns and everyone else is getting rich on them and you're not out there."

He showed them a display of various black-powder models and they were once again intrigued--but as before, had no way of manufacturing. The timing could not have been better for Imperato. He signed a deal with Colt's and Iver Johnson to produce a new line of black-powder models.

It was in Middlesex that all F Series standard production models were manufactured as The Authentic Colt Blackpowder Series. These new F Series 2nd Generation models came in black cardboard boxes with dark gray foam rubber inserts and featured Sam Colt's portrait and signature on the lid and end label.

Unlike their first arrangement, Imperato was now responsible for the entire production of Colt black-powder models. "They were all hand-fitted. There was no way to do mass production," explains Imperato. "We had the barrels, cylinders and backstraps cast in Italy (as Forgett had done), but we finished them off in-house. We made the frames, the center pins, nipples, all of the screws, springs, and built every F Series gun at Iver Johnson Arms. We even used the old style color-case hardening method with the charcoal and bone meal, and Colt's exclusive Colt Blue Finish. They turned out pretty good. In fact, I think our finishes were actually better than Colt's single actions being done in Hartford."

Under the subcontractor agreement to produce 2nd Generation percussion models, Imperato's responsibilities were to manufacture the revolvers to Colt's strict specifications, then ship the finished product to its Hartford facilities. Colt's then performed final inspection and shipped the revolvers to distributors.

This is why Colt historical letters for 2nd Generation percussion revolvers contain exactly the same type of information one finds in letters for original percussion models, Single Action Armys and other models.

Somewhat out of historical sequence, Colt's skipped the First and Second Model Dragoons (later introduced in 1980), and following the 1851 Navy and Third Model Dragoon, next brought out the popular 1860 Army model in November, 1978.

Sam Colt designed the original 1860 Army to be nearly the same size as the 1851 Navy, but in .44, with nearly as much punch as a Dragoon. Colt used the same basic frame as the Navy, but with a slightly longer backstrap and grip, a new rebated cylinder (milled larger in diameter approximately three-quarters of an inch forward of the breech to allow for the larger caliber), and a beautifully contoured, round 8-inch barrel. Bearing the same roll-engraved battle scene as the '51 Navy, it was an immediate success.

"Approximately 129,000 Model 1860 revolvers were issued to U.S. troops for Civil War service--several thousand of them equipped with an attachable shoulder stock, an accessory to allow firing the arm as a carbine," says Colt historian and author R. L. Wilson. "The U.S. government purchased more 1860 Army revolvers than any other model of Colt or any other make of black-powder revolver. This was the staple handgun of the Civil War, and played the same role in the Plains Indian wars, until succeeded by the Colt Peacemaker .45...in 1873."

Some 200,500 1860 Armys were manufactured, making it the third-highest production Colt up to that time.

The Colt black-powder 2nd Generation reprise of the 1860 Army remained in production until 1982 and was offered in a variety of models. The original 1860 style with rebated cylinder was manufactured from November 1978 to November 1982; also with an electroless nickel finish in 1982; with a fluted cylinder from July 1980 through October 1981; and in stainless steel from January 1982 to April 1982.

Colt's also produced a number of special edition Army models. One series was commissioned by the Hodgdon Powder Company in 1979 to commemorate the Butterfield Overland Stage. This was limited to 500 guns with a shortened 51⁄2-inch barrel, and came with an extra cylinder in a French book-style case. Another dozen 1860 Armys were finished in bright nickel and fitted with ivory stocks in 1984. A total of 3001 U.S. Cavalry 200th Anniversary double pistol sets, cased with a shoulder stock and accessories, were produced beginning in 1977. In 1979 a series of 500 cased 1860 Army models were built, and in 1980 a special Interstate Edition of 200 guns, making the Army the most varied of the 2nd Generation.

The Colt 1862 Pocket Navy and 1862 Pocket Police were the next additions to the black-powder line, introduced in December 1979 and January 1980, respectively. The last percussion models introduced by Colt's prior to the 1873 Peacemaker, original pocket pistols were scaled down versions of the 1851 Navy and 1860 Army.

Notes Wilson "Both actually appeared in 1861, just months before the inventor's death, Jan. 10, 1862. Stocks and frames were identical on these revolvers, as was their serial range, caliber and number of shots (.36, five-shot rebated cylinder), and barrel lengths, (41⁄2, 51⁄2 and 61⁄2 inches). A few 1862 Police models--approximately 50--were made in the 31⁄2-inch barrel length Trapper version without the loading lever and with a separate brass ramrod."

The 1862 Pocket Police model was distinguished by its semi-fluted and rebated cylinder, round 1860 Army-style barrel and creeping lever for loading. The Pocket Navy featured a rebated round cylinder, roll engraved with stagecoach holdup scene, and octagonal barrel with hinged-type loading lever.

"The .36-caliber chambering of these medium size revolvers made them highly prized pocket sidearms. As also true with the 1849 Pocket, a number were carried by Civil War soldiers as backup to their single-shot muskets," wrote Wilson in a Colt black-powder sales booklet published in 1978. That 24-year-old booklet is itself (in mint condition) a collectable item today. A rare first printing had a page of Dragoons pictured backward, but most copies were destroyed.

The 2nd Generation Pocket Navy was produced through November 1981, and the Pocket Police through September 1981. With few exceptions, Navy models are found with serial numbers only in the even thousands (48,000) while the Police models are typically found with serial numbers only in the odd thousands (49,000). Both Pocket models were also produced in a limited edition of 500, each in a fitted presentation box with bullet mold, powder flask, percussion cap tin and combination tool. The beautifully styled presentation boxes were affixed with a brass medallion mounted in the lid featuring a cast bust of Samuel Colt and the legend "COLT AUTHENTIC BLACKPOWDER."

The series was produced in 1979 and 1980 within the production serial number run. In addition, a very limited edition of Pocket Navy and Pocket Police revolvers was produced in bright nickel finish with ivory stocks in 1984.

The 1980 Colt black-powder catalog featured yet another historic reproduction, the 1861 Navy, which was added in September and produced through October 1981. The original 1861 Navy was Colt's update on the 1851 and was again chambered in .36 caliber. Interestingly, Colt's did not discontinue the 1851 Navy when the 1861 Navy was introduced--both remained in production through 1873.

The 2nd Generation 1861 Navy followed the original design, fitting the 1851 frame and cylinder with a streamlined Army-style round barrel and loading lever. For sheer style and balanced proportions, the 1861 Navy is often considered the most beautifully designed Colt percussion revolver.

A new line of First, Second and Third Model Dragoons was added in 1980, all of which were introduced in January. The distinguishing characteristics between the three are minor, however one can easily spot a First Model Dragoon by its square back trigger guard and oval cylinder stop slots. The Second Model has rectangular stop slots, and Third Model Dragoons have rectangular stop slots and a rounded trigger guard. All three share a half-round, half-octagonal barrel, 23⁄16-inch cylinder and roll-engraved Texas Ranger and Indian fight scene.

The 1847 Walker was first issued in June 1980, as the Colt Heritage, a limited, cased model complete with a leather-bound and gilt-edged edition of R. L. Wilson's book The Colt Heritage. A total of 1,853 were produced through June 1981. Each Heritage Walker was serialized from 1 to 1,853 with the book, signed by Wilson and numbered to match the gun. A striking presentation, the Walker was set into a fitted case with the book placed in a removable shelf, allowing both the pistol and book to be displayed.

Among the last black-powder models to be reintroduced by Colt's was the 1848 Baby Dragoon, a pocket-sized version of the First Model Dragoon and a throwback to the very first Paterson No. 1, chambered for .31 caliber, limited to five shots and conspicuously absent of a loading lever. (In its place, the cylinder pin doubled as a loading ramrod). Standard barrel lengths for original guns ranged from 3 inches to 6 inches. The 4-inch model was the most popular and that was the barrel length chosen for the 2nd Generation Colt, introduced in 1979 as a limited edition of 500 presentation models each in a fitted case with powder flask, bullet mold, percussion cap tin and combination tool.

Between February 1981 and April 1982, another 1,352 Baby Dragoons were produced for general sales. Old time collector James B. Smith, of Connecticut, lent the original revolver to Colt's that was used to produce this series of 2nd Generation pistols.

Enter The Colt Custom Shop
While Imperato was turning out black-powder Colts by the thousands, a handful were being diverted to the Colt Custom Shop for use in a limited series of factory engraved editions; guns that would become the most rare and valuable members of the 2nd Generation.

"We would ship the guns to the custom shop in the white [an unfinished gray] and they would be completed by factory engravers or, on occasion, sent to American Master Engravers Inc., (including A.A. White, John Adams, Sr., Andrew Bourbon and Denise Therion), or one of the other leading artisans of the day like Howard Dove," says Wilson.

Much of the enthusiasm for finely engraved 2nd Generation Colts was created in 1980-81 by then-Colt Industries chairman, George A. Strichman, who commissioned the most elaborately embellished and costly 2nd Generation models of all. He challenged Al De John's Colt factory engravers and the staff at American Master Engravers to do their best work. The result was a remarkable collection of guns which were the inspiration for Colt Custom Shop limited editions. Most of the Strichman collection is now part of the Autry Museum of Western Heritage in Los Angeles, California. Many of them can also be seen in 'Colt Blackpowder Reproductions & Replicas, A Collector's & Shooter's Guide', available from Blue Book Publications, and in Wilson's 'Colt, An American Legend'.

As shown on the cover of Second Edition Blue Book of Modern Black Powder Values, this U.S. Cavalry Custom Engraved 1860 Army is part of a two-gun set with shoulder stock. Part of the limited edition Cavalry Commemorative model produced from 1977 to 1980, the guns were embellished with class A vine scroll engraving on the barrels, class B engraving on the frames and stock mount, and wolf's head engraving on the hammers. The pair was further embellished with gold barrel bands, gold stars inlaid between each chamber of the cylinder, and the serial number 1 of 40, 2 of 40, etc., engraved on the left side of each frame. Only 23 sets were engraved. The remaining 17 had only the gold embellishments.

Within the Colt custom shop series of engraved 2nd Generation Colt percussion pistols there are a number of variations, some produced in sets of from 20 to 50, but most limited to 10, and a few to single examples.

Among the most desirable are the Colt 150th Anniversary Engraving Samplers produced in both high polish blue and bright nickel finishes, and in a variety of popular models 1860 Army; Third Model Dragoon; 1862 Pocket Navy and Pocket Police. The Samplers featured four different B engraving styles on each revolver, three depicting the work of different engravers from the 19th century and one with contemporary technique. All are mounted with ivory stocks featuring the engraver's names and dates of their work scrimshawed in script on the left grip R. Henshaw 1831, L. Nimshke 1850 -1900, C. Helfricht 1871-1921, and the word "Contemporary." The Colt Custom Shop continued to produce limited editions through the early 1990s from remaining 2nd Generation inventory.

The 2nd Generation (C Series and F Series) lasted for over a decade and included a total of 11 different designs 1851 Navy; 1847 Walker; First, Second and Third Model Dragoons; 1860 Army with rebated cylinder and fluted cylinder; 1861 Navy; 1848 Baby Dragoon, and 1862 Pocket Police and Pocket Navy.

"The best seller was the 1860 Army, just slightly ahead of the 1851 Navy in popularity," recalls Imperato.

The 2nd Generation production came to an end in 1982, bringing to a close another interesting chapter in the history of Colt's.

(This is an excerpt from Dennis Adler's latest book, 'Second Edition Blue Book of Modern Black Powder Values', published by Blue Book Publications.)

Vaya,

Scouts Out!
"It Wasn't Cowboys and Ponies - It Was Horses and Men.
It Wasn't Schoolboys and Ladies - It Was Cowtowns and Sin..."

Offline Tsalagidave

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 909
  • Dave Rodgers
  • Liked:
  • Likes Given: 61
Re: colt 2nd generation cap and ball pistols
« Reply #10 on: July 28, 2011, 11:49:13 AM »
I agree with the folks here that calling a 2nd gen Colt a "dolled up Uberti" is a terrible disservice to the gun. I have owned several Italian made black powder pistols and when I started collecting 2nd gen colts, the difference was night and day. The 2nd gen navy-six I carry is a workhorse. Aesthetically, it is more appropriate if you are trying to nab the authenticity down to the closest details. Performance wise, the mechanics are crisper and it chews up and spits out spent caps all day long. Jams that have required me to dismantle my regular Italian repros have been resolved by thumbing back the hammer for another shot with my 2nd gens.

-Dave
Guns don't kill people; fathers with pretty daughters do.

Offline Marshal Deadwood

  • SHOOTER FOR HIRE
  • Top Active Citizen
  • *
  • Posts: 1382
    • Home of the Plainsmen
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #11 on: July 28, 2011, 01:27:12 PM »
That is the problem I've had with Italian percussion revolvers. Not so much the cap that sticks between the frame and cylinder,,,but the minute pieces that get in the insides and results in me taking the revolver totally down to clean it out.

Offline Fox Creek Kid

  • Top Active Citizen
  • *
  • Posts: 4558
  • Liked:
  • Likes Given: 104
Re: colt 2nd generation cap and ball pistols
« Reply #12 on: July 29, 2011, 12:17:41 AM »
That is the problem I've had with Italian percussion revolvers. Not so much the cap that sticks between the frame and cylinder,,,but the minute pieces that get in the insides and results in me taking the revolver totally down to clean it out.


You need Treso nipples & Rem. #10 caps. This will solve that.

Offline Marshal Deadwood

  • SHOOTER FOR HIRE
  • Top Active Citizen
  • *
  • Posts: 1382
    • Home of the Plainsmen
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #13 on: July 29, 2011, 01:47:22 AM »
Thank you, Fox Creek.

Offline Fingers McGee

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 1397
  • Smoke & Fire
  • SASS #: R28654
  • NCOWS #: 3638
  • Liked:
  • Likes Given: 6
Re: colt 2nd generation cap and ball pistols
« Reply #14 on: July 29, 2011, 11:26:28 PM »

You need Treso nipples & Rem. #10 caps. This will solve that.

What he said  ;D
Fingers (Show Me MO smoke) McGee;
SASS Regulator 28654 - L - TG; NCOWS 3638
AKA Man of many Colts; Diabolical Ken's alter ego; stage writer extraordinaire; Frontiersman/Pistoleer; Rangemaster
Founding Member - Central Ozarks Western Shooters
Member - Southern Missouri Rangers;
NRA Patron Life: GOA; CCRKBA; SAF; SV-114 (CWO4 ret); STORM 327

"Cynic:  A blackguard whose faulty vision sees thing as they are, not as they should be"  Ambrose Bierce

Offline rosinghania

  • Citizen
  • *
  • Posts: 13
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #15 on: July 31, 2011, 03:32:12 AM »
I had the 1851 model from my grandpa which got busted over a year ago. Would it be better to just sell it rather than buying overpriced parts?

Offline Major 2

  • "Still running against the wind"
  • Deputy Marshal
  • Top Active Citizen
  • *
  • Posts: 15832
  • NCOWS #: 3032
  • GAF #: 785
  • Liked:
  • Likes Given: 415
Re: colt 2nd generation cap and ball pistols
« Reply #16 on: July 31, 2011, 08:27:27 AM »
I had the 1851 model from my grandpa which got busted over a year ago. Would it be better to just sell it rather than buying overpriced parts?


Is it and old beater Brass Frame ?  what is broken,  just a spring or is worn out or shot loose ?

 I'll put it like this.... how much does the gun mean to you ?
If your Grandfather gave it to you, it meant something

I have a Replica Flint Hawkins .... My Dad gave me on my Birthday, the last year of his life...to me it is priceless
when planets align...do the deal !

Offline PJ Hardtack

  • American Plainsmen Society
  • Top Active Citizen
  • *
  • Posts: 4003
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #17 on: August 13, 2011, 09:06:26 PM »
I've got a Colt 2nd gen 3rd Model Dragoon and a '51 Navy. The Dragoon is far and away my favourite cap & ball gun. It came to me with a broken bolt/trigger spring, long since repaired. Now the Navy done busted her spring .... ;>(
I had a spare on hand that required shortening the trigger arm of the spring close to 1/16th inch. Going to order spares for both guns from VTI.
While I had the '51 apart, I noticed how light the grip frame and trigger guard were. I put a magnet to them and surprise, surprise ... not made of steel! I presume silver plated brass.
I have to admit that both have a little more cachet to them than the best of the spaghetti guns, but I have pals with late model Ubertis that aren't anything to be embarrased about.
Forgot to add ..... while I haven't miked the chamber mouths or bore diameter of the Dragoon, it shaves off a ring of lead from .451 diameter ball. It also groups well, letting me hit an Ace of Spades card in a match at 15 yds. I fired a rd holding at six o'clock, saw that it hit about 9" high and managed to hit it twice more. Load was 50 grs FFg.  Several cartridge guns failed to hit it at all.
"I won't be wronged, I won't be insulted, I won't be laid a hand on.
I don't do these things to others and I require the same from them."  John Wayne

Offline Hoof Hearted

  • Cartridge Conversion Specialist
  • Deputy Marshal
  • Top Active Citizen
  • *
  • Posts: 1734
  • If your not an FFL you’re not a gunsmith
    • Cartridge Conversion
  • SASS #: 8038
  • NCOWS #: 3809
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #18 on: November 21, 2011, 11:00:14 PM »
Jim Davis tells me that Lou Imperato contracted with ASM for the parts mentioned here as "cast in Italy":

It was in Middlesex that all F Series standard production models were manufactured as The Authentic Colt Blackpowder Series. These new F Series 2nd Generation models came in black cardboard boxes with dark gray foam rubber inserts and featured Sam Colt's portrait and signature on the lid and end label.

Unlike their first arrangement, Imperato was now responsible for the entire production of Colt black-powder models. "They were all hand-fitted. There was no way to do mass production," explains Imperato. "We had the barrels, cylinders and backstraps cast in Italy (as Forgett had done), but we finished them off in-house. We made the frames, the center pins, nipples, all of the screws, springs, and built every F Series gun at Iver Johnson Arms. We even used the old style color-case hardening method with the charcoal and bone meal, and Colt's exclusive Colt Blue Finish. They turned out pretty good. In fact, I think our finishes were actually better than Colt's single actions being done in Hartford."
Anonymity breeds bravado.......especially over the internet!
http://cartridgeconversion.com
http://heelbasebullet.com
aka: Mayor Maynot KILLYA SASS #8038
aka: F. Alexander Thuer NCOWS #3809
STORM #400

Offline Pancho Peacemaker

  • NCOWS Texican Senator
  • NCOWS Member
  • Top Active Citizen
  • ***
  • Posts: 1560
  • NCOWS #3120, SASS #75813
    • Pancho's Videos
  • Liked:
  • Likes Given: 0
Re: colt 2nd generation cap and ball pistols
« Reply #19 on: March 08, 2012, 01:01:28 PM »
These 2nd generation C&B Colts have always interested me as a collector, but I've never taken the plunge and bought any.

How is the market price on these guns (NIB - collector grade) lately?


Pancho
NRA - Life
NRA-ILA
TSRA - Life
S&W Collectors Association

 

"A vote is like a rifle: its usefulness depends upon the character of the user."
-T. Roosevelt (1858 - 1919)

 

SMF spam blocked by CleanTalk

© 1995 - 2023 CAScity.com